这个翻边起一种密封垫的作用。
这个翻边起一种密封垫的作用。
我要一条没有翻边的裤子。
该机适合皮革、皮包、鞋面折边、翻边。
The machine apply for leather handbags or instep folding turn edging.
本机型适合皮革、皮包、鞋面折边与翻边。
The machine apply for leather handbags or instep folding turn edging.
介绍翻边瓦铣槽夹具的设计原理及使用效果。
The paper presents the design principle and application results of the flanged slotting clamp.
该机适合皮革、中底包边、皮包、鞋面折边、翻边。
The machine apply for leather handbags or instep folding turn edging.
在圆孔翻边过程中，变形程度是用翻边系数来描述的。
Deformation extent is described by burring factor in the process of round hole burring.
穿翻边短裤要谨慎，因为它会让你看起来像妈妈辈人物。
Be careful with cuffed shorts since they can appear quite mom-ish.
该模型考虑厚向(平均)各向异性系数对翻边高度的影响。
The influence of average normal anisotropic coefficient on the flanging height can be considered in this model.
塞缪尔用手指勾住她的裤攀，低头看着她的翻边牛仔裤和粉红色拖鞋。
Samuel hooks his fingers through her belt loops, looks down at her cuffed jeans and pink slippers.
专业设计，适用各种零部件的翻边铆合作业，如球头、硅油离合器等。
Professional design, suitable for various parts of the flange riveting, such as ball, silicone oil clutch. etc.
利用有限元技术，对凸翻边钣金零件的高压橡皮成形过程进行模拟分析。
FEM has been used to simulate and analyze the high pressure rubber forming process of part with flange bending.
采用关联设计思想，实现翻边模模型参数的输入与结构再设计的和谐统一。
The system uses associated design idea in order to realize input of flanging die model parameter and harmonious unification of structure redesign.
同时，以一翻边精度要求较高的零件为例，介绍了一种倒装式结构的翻边模。
Meanwhile, as a part needs high precision as flanging for example, flanging die with hyperbatic structure is described.
分析了角部雨檐零件特点及其成形机理，将复合成形分解为简单的弯曲和翻边。
The characteristics of the corner rain eaves parts and their forming principle were analyzed. The compound forming was broken into simple bending and flanging.
改进了的旧的骨架翻边整形模，采用自动哈夫成形，解决了零件出模困难的问题。
The flanging-sizing die structure of the exo-skeletal was improved, using auto-half block, solved the difficult problem of part out off die.
缩颈翻边组合机是对马口铁空罐罐身的一端或两端进行缩颈与翻边的一种组合设备。
The novel necking and curling combination machine is a kind of combination equipment for can_body forming.
影响翻边成型性和成型精度的一个重要因素就是零件修边后的形状和尺寸是否合理。
The shape and dimension after trimming is the most important factor which affects the forming precision.
对固定支架成形的变薄引伸、翻边的工艺进行了分析，对出现的问题提出了解决办法。
This paper analyzes the stretching and turning edge process of big deformation for an array turning edge-hole and proposes some solutions to the problems.
介绍在特殊夹层压力容器制造中对夹层壳体壁上进行开孔翻边热冲压成形的工艺技术。
This article describes a hot pressing formation technology to make flanged openings on special jacketed vessel shells.
分析了后减震器帽的成形工艺，介绍了成形该零件的拉深模、翻边模以及旋压模具结构。
The forming technology of rear shock absorber cap is analyzed, and its drawing die, flanging die and spinning die structure are also introduced.
介绍形成小圆角半径的圆孔翻边模具的结构特点，按体积不变的原则，推导了计算公式。
Die structure based on the process of forming small fillet radius is introduced, and deduced the formula according to the principle of volume invariably.
但是，如果，例如，您使用您的翻边工具仅一年几次，你应该在每次使用前，刷新你的记忆。
But if, for example, you use your flaring tool only a couple of times a year, you should refresh your recollection before each use.
论述了在薄板冲压件上，用变薄翻边冲制小螺纹底孔的工艺、冲模结构、设计与制作技术。
Discuss punching small thread fluted opening technology, die structure, die design and die manufacture technology on thin sheet.
车身零件翻边前一般有修边工序，需要准确的修边线，否则翻边后零件达不到零件尺寸要求。
Before flanging auto-body panels, a feasible trimming line should be obtained, otherwise the final part shape after flanging cannot meet the dimensional requirement.
针对方孔翻边问题进行了编程式参数化有限元法研究，其结果与现有文献试验结果基本吻合；
The programming PFEA approach is researched by square hole flanging, and the result accords with the experimental result from publications.
本系列风机的叶片采用特殊扭曲孤度设计，机壳采用法兰翻边工艺，使风机噪音更低，风量更大等特点。
SF (b) series adopt special twisted blade design and flange flanging casing, which makes the noise lower and the air volume larger.
本系列风机的叶片采用特殊扭曲孤度设计，机壳采用法兰翻边工艺，使风机噪音更低，风量更大等特点。
SF (b) series adopt special twisted blade design and flange flanging casing, which makes the noise lower and the air volume larger.
应用推荐