阐述幕墙自平衡体系结构有限分析计算软件的研究。
A study on finite analysis calculation software of the curtain wall self-balance structure is presented.
通过对有限元分析软件ANSYS与工程设计软件TBSA计算结果的比较，总结出在框支剪力墙结构设计中应该注意的一些问题。
Through comparing the results between ANSYS and TBSA, a designing software, summarized some questions that we should pay attentions when designing the frame-supported shear wall structure.
在磁体结构设计中，本文采用有限元软件分别对单、双环形永磁结构进行了分析计算。
To design the magnet structure, finite element method is used to analyze the permanent magnetic field.
因此对大型结构分析软件ANSYS的三维非线性计算功能进行了深入研究，在此基础上完成了基于非线性有限单元法的高拱坝坝肩稳定计算分析。
Basic theory of nonlinear FEM analysis and its realization in ANSYS were studied. Accomplish stability analysis of high arch dam abutment based on nonlinear FEM analysis.
作者利用ANSYS有限元分析软件对一个平面桁架模型进行了模态分析，并用APDL语言编制程序计算该结构的柔度差值曲率。
ANSYS is used to make the modal analysis of a plane truss structure model, then APDL is used to compile procedures to calculate flexibility difference curvature.
通过运用大型有限元结构分析软件，建立全桥组合有限单元模型对全桥结构进行计算分析。
General purpose analysis software is applied to establish and calculate a model of integrated finite element model for whole bridge.
建立了U形无加强波纹管结构分析的有限元分析模型，采用ANSYS有限元软件对其在不同平面失稳工况下的应力响应进行了计算。
The finite element analysis model to the U shape bellows is presented and calculated by the ANSYS program under diverse loads for in plane instability.
以镜架支撑安装基面上实测的地面振动速度功率谱密度为激励，运用ANSYS有限元分析软件的PSD分析模块，对该结构系统的随机振动响应进行了分析计算。
The PSD measured on the install base level of the mount as the excitation, the random vibration response of the mount was analyzed with the PSD module of ANSYS.
应用薄壳理论和ANSYS有限元分析软件对典型结构的应力分布进行了计算，同时应用X射线衍射法对该结构的应力进行了测试。
The distribution of residual stress in typical configuration is calculated by using theoretical formulae and ANSYS. In the same time it is measured by X-ray diffraction.
利用有限元计算软件进行了结构模态分析，通过参数分析找到了各参数与结构振动频率之间的关系。
Then modal analysis is performed by using finite element method. In this way, the relations between parameters and structural vibration frequency are figured out by parameter analysis.
本文以大型有限元分析软件ANSYS为计算分析平台，开发了发动机涡轮静子结构优化设计系统。
Based on ANSYS - a large finite element analysis software for calculate and analysis platform, a system developed for the design optimization of turbine stators.
最后以重庆地维长江公路大桥为例，利用大型有限软件ANSYS对桥梁进行结构分析计算。
Take the Chongqing Diwei Changjiang road bridge as an example, and use ANSYS to analyse the bridge structure.
利用ANSYS有限元计算软件，采用接触非线性与耦合自由度两种方法对亚硫酸罐车车体进行有限元结构分析，并就两种方法的计算结果作了详细的对比。
Taking ANSYS Workbench as a tool, this paper simulates well the bearing-conjunction problem by means of building nonlinear contact between ball and rolling channel of bearing.
利用ANSYS有限元计算软件，采用接触非线性与耦合自由度两种方法对亚硫酸罐车车体进行有限元结构分析，并就两种方法的计算结果作了详细的对比。
Taking ANSYS Workbench as a tool, this paper simulates well the bearing-conjunction problem by means of building nonlinear contact between ball and rolling channel of bearing.
应用推荐