左侧较大的紧固螺母松动,需要修理或更换。
The large securing nuts on the left side are loose and need to be repaired or replaced.
筒体螺栓的紧固螺母和筒体外壁之间也采用橡胶垫圈密封。
A rubber gasket seal is used between a clamp nut of a barrel screw bolt and the outer wall of the barrel body of the utility model.
为了在每个螺母上获一至的压力,建议用扳手或相关的计量装置紧固螺母注意:此时装置如果处于无泄漏状态,可能引起盘根燃烧。
In order to be one on each nut to the pressure, it is recommended to use wrenches or nut fastening the measuring device Note: at this point if the device is leak-free state, may cause burning packing.
将地脚螺栓连接板用螺母紧固。
在调节完成后,紧固锁紧螺母,重新安装快速进水手柄帽。
After completing adjustments, tighten the lock nut and replace the fast fill lever cap.
因此,在调节管接螺母的紧固度时,阀座对球体的压力就一直存在着。
Thus, by adjusting the tightness of the union nut, the squeeze of the seats against the ball would be maintained.
试车前务必检查所有螺栓、螺母是否有松动,若有松动的螺栓、螺母必须重新紧固。
Make sure check the bolt and nut before testing run. and if they become less crowded, fastening again.
用螺纹联接并起紧固作用的零件称为螺纹紧固件。常用的螺纹紧固件有螺栓、双头螺柱、螺钉、螺母、垫圈等。
Parts with threads used for joining and fastening are called screw fasteners. The most widely used components as screw fasteners are bolts, double screw bolts, screws, nuts, washers.
注:如果出现少量的泄漏,则拆卸锁紧螺丝,然后锁住垫圈和阀盖,然后轻轻紧固填料压紧螺母。
NOTE: If minor leakage occurs, remove lock screw, lock washer and cap and lightly tighten packing gland nut.
单进入阀门-小心紧固单活接头螺母。
True Union Valves - remove valve; CAREFULLY tighten seal carrier (located on inlet end of body).
因此,应定期对螺栓和螺母进行检查并实施紧固,以减少不必要的费用。
Therefore, we should regularly inspect the bolt and nut fastening and implemented in order to reduce unnecessary costs.
孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening Angle.
现在我司主要生产紧固件产品中的螺母类系列的产品。
Now my main production Fastener Products Division in the nut category range of products.
压铆:指采用冲床或油压机把压铆螺母、压铆螺钉或压铆螺母柱等紧固件牢固地压接在工件上的工艺过程。
Riveted: refers to use of press or hydraulic press to riveted nut, riveted screw or rivet nuts and other fasteners column firmly crimping the workpiece on the process.
如果阀杆周围出现泄漏,则轻轻紧固压紧螺母。
螺栓:通常与螺母一起用于连接两个或更多零件的机械紧固件。
Bolt: Mechanical fastener, usually used with a nut, for connecting two or more parts.
现在我厂主要生产紧固件产品中的螺母、平垫圈类系列的产品。
Now my main production plant in fasteners products nut, plain washer series products.
连接调整器。把调整器紧固在钢瓶上,安全地上紧入口螺母。
Attach the regulator. Fasten the regulator to the cylinder and tighten the inlet nut securely.
单进入阀门-小心紧固单活接头螺母。
紧固件、连接件、车削件、压铆螺母、空心螺母、非标件。
The fastener, the bridge piece, the turning, presses the riveting nut, the hollow nut, non-tender.
安装安全阀阀盖螺母,并加以紧固。
以德国精湛、先进的制造工艺和技术为依托,专注于大型螺栓螺母紧固、拆装科技及液压实用动力的运用。
Germany skilled, advanced manufacturing processes and technologies, focus on the large nut fastening bolt, disassembly of hydraulic technology and practical application of driving force.
上海凌锐紧固件有限公司是一家专业生产和销售各类高强度螺栓,螺母,垫片及各种非标件的制造商。
Shanghai Lingrui Fasteners Co., Ltd is a manufacturer of various kinds of high strength bolts, nuts, washers and various non-standard parts.
即唐氏螺纹紧固及硬锁紧螺母紧固。
主营产品:各种紧固件、标准件、螺栓、螺柱、螺丝、螺钉、木螺钉、自攻螺钉、车削螺丝、组合螺丝、螺母、连接件、平垫、挡圈等。
Main products: various kinds of fasteners, standard, bolts, screws, bolts, screws, wood screws, tapping screws, turning the screw, the combination of screws, nuts, fittings, flat mat, ring, etc.
凸出翼结构的采用比普通螺母增加了金属与金属间的接触面,起到楔入紧固的作用,防盗性能更卓越。
Compared with the common nut, a contact surface between metals is added by adopting the protruded wing structure, plays a role of wedging and fastening and has more excellent theftproof performance.
通过试验和理论分析厚、扁螺母在紧固过程中的受力情况,并从试验结果得到一个较合理的厚螺母拧紧力矩,既能保证塔式起重机的安全运行,又能延长螺栓的使用寿命。
Changing the positions of thin and thick nuts and using the right thick nut tightening torque ensure safe operation of the crane and longer lives of the screws.
邯郸市通和紧固件制造有限公司,是一家专业生产火花塞配件、内爆膨胀螺丝、内迫壁虎、套筒扳手、螺母、扣件螺丝的专业公司。
Handan Tonghe Fastener manufacturing co. Ltd. is a company specialized in manufacturing fittings for spark plug, inner expansion bolts, drop-in anchor, socket wrench, nuts and screws.
邯郸市通和紧固件制造有限公司,是一家专业生产火花塞配件、内爆膨胀螺丝、内迫壁虎、套筒扳手、螺母、扣件螺丝的专业公司。
Handan Tonghe Fastener manufacturing co. Ltd. is a company specialized in manufacturing fittings for spark plug, inner expansion bolts, drop-in anchor, socket wrench, nuts and screws.
应用推荐