最后，提出了保证系统测量精度的方法。
At last, measure for improving system measurement accuracy is proposed.
以此直线方程校正网格区间内的系统测量坐标。
We calibrate system measure coordinates of every grid area according to the linearity equation.
该方法的核心是系统影响方程和系统测量方程。
The kernel of this method consists in system measuring equations and system effective equation.
总结提高激光导向系统测量精度应采取的措施。
Finally, the measures to improve the surveying precision of the Navigation System are summarized.
视差现象的存在影响了望远系统测量瞄准的精度。
Parallax can effect the precision of telescope system when measuring and aiming.
本文介绍一种TLD系统测量程序的简易优化方法。
This paper describes the simple optimizing method of TLD system measurement procedure.
电磁式电压互感器是电力系统测量电压的主要装置。
The magnetic type PT is the primary equipment for measuring the voltages in power system.
最后本文给出了应用本系统测量电机声功率的例子。
An example of sound intensity measurement for electric motor is presented.
本文主要介绍涡轮增压系统测量分析系统的研制和相关的试验。
This paper mainly introduces the development of measurement and analysis system for the turbocharger and relative experimental investigation.
又以标准圆柱体作为测量实例，证明了测量系统测量的准确性。
And the standard cylinder is also measured. The measurement proves the veracity of the system measurement.
采用等动采样方法对旋风管内的颗粒浓度分布进行了系统测量。
The distribution of particle concentration in the cyclone tube was measured by isokinetic sampling method.
根据计算结果及其分析，给出了检测系统测量装置的设计参数。
On the basis of the results and analysis, the requirements of design scheme for measuring apparatus are given.
文中介绍了应用该仪表系统测量火花等级来诊断电机故障的例子。
As an example, it is recommended to diagnose the fault of motor by measuring the rank of spark with this system.
辨认系统测量的东西包括像鼻子的大小和位置，双眼之间的距离以及颧骨的形状。
Recognition systems measure things like the size and position of a nose, the distance between the eyes and the shape of cheekbones.
结果表明，该系统测量精度高，现场适应性强，具有较高的使用价值。
The results show that the system has high measuring accuracy, high applicability at the site and relatively higher practical value.
基于相关流速理论所建立的虚拟仪器系统测量坡面径流流速是可行的。
Measuring slope flow velocity using virtual instrument system based on cross-correlation theory was feasible.
用计算机图像分析系统测量脐带静脉的几何形态及显微结构成分的含量。
The geometrical morphology data and the relative contents of microstructure of umbilical cord vein were measured by the computer image analysis system.
在满足系统测量精度条件下，使用反向优选算法优化r BF网络结构。
In case of satisfying measure accuracy, backward selection method reduces the architecture of RBF networks.
使用长腿圆规或电子测量系统测量各对角的抬起点，然后比较其是否对称。
Measure pickup points diagonally using a beam compass or an electronic measuring system and compare the symmetry.
光镜观察后，用计算机图像分析系统测量其中膜显微结构成分的相对含量。
The microstructure component in tunica media of umbilical cord vein were measured by the computer image analysis system.
应用无线电近导系统测量的距离和方位校正惯导是一种新的综合导航方式。
It is new mode in integrated navigation that INS is corrected with distance and orientation measured by wireless navigation system.
这些系统测量精度高、速度快、自动化性能强，成为工件加工的质量保证。
The system has high measuring accuracy, fast machining speed and better automaticity, becoming the quality assurance of work machining.
该系统测量精度高，安全可靠，能实时监测车身侧面与障碍物之间的距离。
It can detect the distance between the side of vehicle and the obstacle in real time.
研究表明，利用三维激光扫描系统测量树冠体积具有较强的实践意义和应用价值。
It shows that using the three dimension laser scanning and mapping system for measuring tree crown volume is practical and applicable.
调试和运行结果表明，该系统测量精度高、性能良好，其设计完全满足工程要求。
Tests and operation results indicate that the system has high measurement accuracy and good performance, and its design totally meets the project requirements.
在硬件电路设计中，信号调理电路和数据采集卡是整个系统测量精度的关键环节。
During the hardware circuit design, the signal conditioning circuit and the DAQ card is important to whole system's accuracy.
横断取材，冰冻切片，HE法染色，用计算机图像分析系统测量其几何形态学指标。
Serial sections were obtained by frozen section methods and stained by HE. The geometrical morphology data of umbilical cord vein were measured by the computer image analysis system.
通过该系统测量爆震管中火焰传播速度的轴向分布，确定了爆燃到爆震的转捩距离。
This system was used to measure the flame propagation velocities along the tube, and furthermore to determine the DDT distance.
设计了系统标定方法，给出了详细的标定步骤和实验数据，最终得到系统测量结果。
We put forward the calibration method and list the detailed calibration process and data, then acquire system measurement results.
设计了系统标定方法，给出了详细的标定步骤和实验数据，最终得到系统测量结果。
We put forward the calibration method and list the detailed calibration process and data, then acquire system measurement results.
应用推荐