钢管口应先装上管螺母,以免穿线时损伤导线绝缘层。
At first, pipe bolts should be erected at the nozzle so as to prevent the insulation coat of the conductor from being damaged while wiring.
对风机及电动机的电源电压、频率、功率,盘管规格,加湿器种类,空气过滤器形式及效率,配管口径及方向等有要求时请注明;
About the supply voltage, frequency, capacity factor of the fan and motor, specification of coil pipe, kinds of humidifier, form and efficiency of air filter, caliber and direction of pipe and etc.
为满足泵管口的受力要求,提出了采用波纹管补偿器时应采取的措施。
Measures for adopting bellows expansion joint have been proposed to meet the requirement of allowable force in the inlet of pump pipeline.
在根管口段,两组间无显著性差异(P>0.05)。 两组间根管预备时间无统计学差异(P>0.05)。
There was no significant difference between the two groups at the coronal level (P>0.05) as well as preparation time (P>0.05).
方法:检查了23例干燥下颌骨标本,测量了舌侧管的数目、位置、管口直径、长度和走向。
Methods: On23dry mandibles, the number, location, diameter, length and direction of lingual vascular canals were measured.
目的研究上颌第一磨牙根管口形态和位置关系,为根管治疗时寻找根管口提供解剖学依据。
Objective To study the shape and location of root canal orifice in maxillary first permanent molar and provide a morphological basis for locating canal orifice in endodontic therapy.
从控制成型残余应力峰值和合缝预焊后管口椭圆度的角度出发综合考虑,将管坯成型为扁椭圆较为合理。
It is reasonable takes shape the unfinished piping to the flat ellipse for reduce the remaining stress peak value and ellipticity.
1号货舱的右污水井测深管的螺纹部分也被腐蚀而且管口盖遗失。
Also the starboard bilge sounding pipe of No. 1 cargo hold was corroded at the thread section and the closing cap was missing.
技术系统包括用作入射器的加速器、高能加速器(可采用同步回旋加速器)、射束输送管、旋转架质子输送和射线管口、治疗床、管制次系统等。
Technical system includes the injector and the accelerator subsystem, synchrotron, beam transport, gantry with beam transport and nozzle, treatment couch and control subsystems etc.
分支装置使用管托状的密封件通过主管上的管口将支管连接到主管上。
A branching device connects a branch pipe to a main pipe through an orifice in the main pipe utilizing a saddle-like sealing member.
内接续管为热镀钢制件,外续管口及两端衬管为铝制件。
The inner sleeve is hot-dip galvanized steel, the outer sleeve and lining sleeves are aluminium.
由于介质原因造成腐蚀,使一台丙烯冷凝器管板上大面积的管口焊缝失效发生泄漏。
Because of condenser caused by mediums, leakage occurred in the large-area welding between pipe connect of a C_3H_6 condenser tube sheet.
平板金属膜底面中央贴设有真空吸附管口,真空吸附管连接真空吸附装置的出口。
A vacuum adsorption nozzle is stuck on the center of the bottom surface of the metallic film of the flat plate, and a vacuum adsorption pipe is connected with an outlet of a vacuum adsorption device.
平板金属膜底面中央贴设有真空吸附管口,真空吸附管连接真空吸附装置的出口。
A vacuum adsorption nozzle is stuck on the center of the bottom surface of the metallic film of the flat plate, and a vacuum adsorption pipe is connected with an outlet of a vacuum adsorption device.
应用推荐