Typesafe的Akka更是极大地简化了分布式处理模型，让您可以使用Erlang那样健壮的基于消息的计算。
From Typesafe you have Akka that greatly simplifies the distributed processing model to give robust messaging based computing like Erlang.
将铰接式车辆简化成六自由度的动力学系统，建立了能反映率体平面运动和横向摆动的动态数学模型。
In this paper, the articulated vehicle is simplified to a six-free-degree system in dynamics, and a dynamic mathematical model was derived and established.
在分析了外设动力式采煤机锚链牵引特性的基础上，将其动力学模型简化为具有质量的弹簧—质量系统。
On the basis of analyzing traction property of anchor chain of the shearer operated by outside power, the kinetic model is simplified as spring_mass system with mass.
为了简化吸收循环热力学分析方法，通过吸收循环和压缩式循环的对比，提出吸收循环卡诺模型分析方法。
The Carnot analysis method was proposed for the simplification of the thermodynamic analysis of the absorption cycle, by the comparison of the absorption cycle and the compression cycle.
建立了有内导向瓣周边式对接机构的两空间飞行器对接过程的动力学模型，建模中将对接系统简化为主动飞行器、被动飞行器和主动捕获环三体问题。
The mathematical models of docking dynamics in the process of capture are established for two spacecrafts with inner guide petal peripheral docking mechanisms.
本文使用拟合多项式描述汽车发动机负荷特性，提出结构简化的汽车速度和方向控制模型。
This paper USES polynomials to express the load characteristics of the automobile engine, and presents simplified structure velocity and direction control models.
利用ADAMS软件建立了考虑绳索和柔性梁的自动化立体仓库巷道式堆垛机的简化模型。
A simple modeling method of a laneway stacker crane in automatic stereoscopic warehouse is introduced using ADAMS with ropes and flexible beams considered.
对于以封闭式盒段组合结构为特征的卫星电子设备，讨论了其有限元模型的简化建模方法。
The discussions of the simplified finite element modeling method of the satellite electronic equipments with closed box segment combination structure are given.
作者在最小二乘法的基础上，提出分段直线拟合算法来代替多项式曲线拟合，从而达到简化数学模型的建立和减少计算量的目的。
The author proposes a sectional line fitting to re - place the polynomial curve fitting, which results in simplifying establishment of mathematical model and reducing the amount of calculation work.
根据达西公式及相对渗透率曲线和毛管压力曲线的表示式，提出了一个描述水锁机理及其影响因素的简化的数学模型。
This paper presents a simplified mathematical model for describing the water block mechanism and its influences, based on Darcy's formula and relative permeability curve and capillary pressure curve.
介绍了基于单向运动机构的伸缩式管道机器人工作原理，对管道机器人整机系统进行合理简化，得到等效系统模型。
First introduce the working principle of the inchworm in-pipe robot based on unilateral movement mechanism, and then an equivalent system model is founded after simplifying the whole robot system.
在简化的分布式制造管控系统模型设计中的应用，说明了它的实用性和通用性。
Its practicability and versatility were exhibited by the application to the model design of a simplified management and control system of distributed manufacturing.
基于滑移线场的简化流动模型，运用数学方法求解出了一种锥形模正挤压变形力的最佳上限解，并将该上限解用通用解析式表达出来。
The deforming force of cone-die direct extrusion is solved by a mathematic method based on the simplified flow model of slip line field.
通过对示踪剂质量浓度方程的简化处理，给出了一种简化的数学模型，以及一种简化模型的隐式差分格式。
In this paper, a simplified mathematical model on tracer density equation is given, and an implicit difference scheme on the model is derived.
将轿车三枢轴式等速万向节的三维模型经过结构简化离散成有限元模型，并应用ANSYS软件对其承受极限转矩时的内部接触应力进行有限元分析。
A finite element(FE) model for a tripot universal joint is developed, and a FE analysis on the contact stresses in the parts of the joint under extreme torque is conducted using ANSYS software.
针对复合衰落信道的复杂性，提出了一种简化的信道模型来研究分布式天线系统的误比特率性能。
Due to the complexity of the composite fading channel, a new simplified channel model is proposed to analyze the bit error ratio(BER)performance of the distributed antenna system(DAS).
针对多孔介质特殊的孔隙结构特征，建立了一个新的简化孔隙力学模型，并由该模型导出了渗透率与有效应力的二次多项式关系。
A new simple pore mechanics model is established based the pore structure of low permeability reservoir rock, from which the quadratic equation of effective stress and permeability can be educed.
首先，基于简化的软着陆动力学模型，通过求解特殊两点边值问题，给出了一种实时显式制导方法。
Firstly, based on simplified dynamics of lunar soft landing, an explicit guidance law was induced by solving the special two-point boundary value problem.
对多孔介质体积平均理论进行简化，得到简化的热质传递干燥模型，用一个理论式表达模型中有效扩散系数。
Based on the fact, a simplified drying model of heat and mass transfer is deduced from volume average theory.
针对开放式控制器的原有结构，提出了一种融合网络的简化分层控制模型。
This article studies the former open architecture robot controllers and comes up with a simplified layered control system based on network.
以铸钢冷却壁的传热为研究对象，根据热态试验结果，提出简化传热关系式，并将其与神经网络技术相结合，形成冷却壁热面温度预测仿真模型。
Heat transfer of cast steel cooling stave is the research object, and simplified heat transfer formula is proposed based on thermal state test results.
隐式锚杆单元隐含在岩体单元中，极大地简化有限元模型划分。
The implicit bolt elements are combined in the elements of rock mass, so the mesh generation is extremely simplified.
结合合理的简化条件，建立绕线式双馈风力发电系统的数学模型。
Combined with reasonable simplified conditions, the paper establishes the model of the DFIG system.
它定义了一种以数据为中心的数据发布一订阅模型，提供了一个与平台无关的数据模型，以简化分布式系统中数据的有效发布。
It defines a data-centric data publish-subscribe model, and provide a platform independent model to simplify the data distribution effectively in the distributed system.
利用ABAQUS软件的显式积分计算模块，建立了一种简化的旋压加工模拟计算模型。
With the ABAQUS explicit integral model, a simplified simulating model for the power spinning was presented.
本文对绝热式合成氨反应器，提出一种双线性简化模型。
A bilinear model of adiabatic ammonia reactor has been developed.
文中建立了这种情况下的分布式目标模型，提出了分布式目标的空间二维参数估计简化算法。
In our paper, it is presented a simplified distributed signal estimation method based on a special model, and computer simulations confirm the method presented.
同时还提出了一个简化的气液同轴式喷嘴流量计算模型。
A simplified theoretical model is developed to calculate the flowrates of gas-liquid coaxial atomizers. The comparison between the theoretical and experimental results shows a reasonable agreement.
同时还提出了一个简化的气液同轴式喷嘴流量计算模型。
A simplified theoretical model is developed to calculate the flowrates of gas-liquid coaxial atomizers. The comparison between the theoretical and experimental results shows a reasonable agreement.
应用推荐