结果表明，“函数缝”方法便于新程控接口的扩展，同时简化了程序结构。
By this method, it is easy to add new programmable interface and the program structure is simplified as well.
根据低压程控电源程控接口的特点，阐述了程控电源PC总线控制板卡的设计原理。
According to the characteristics of program controlled interface in low voltage programmable power supply, the design principles of PC bus board in programmable power supply are described.
对于远程控制，需要一个远程和红外线接口。
For remote control, a remote and an infrared interface is necessary.
本文讨论了如何设计具有IEC- 625标准接口的可程控开关器。
In this article it is discussed how to design programmable switch with iec-625 standard interface.
所有功能可于前面板，可远程控制，通过其中的接口。
All functions available on the front panel can be controlled remotely through one of these interfaces.
模拟用户线接口电路是数字程控交换系统的重要组成部分。
Subscriber line interface circuit is an important part of digital program-controlled switching system.
本dds程控正弦信号发生器系统基于计算机串行接口。
This DDS program-controlled sine signal generator system is based upon computer's serial interface.
近年来，各种配有IEEE- 488标准通用仪表接口的程控仪器和自动测试系统不断涌现。
In the recent years, all kinds of program-controlled instruments and automation testing systems that are configured by common instrument interfaces of IEEE-488 standard have come forth continually.
提出了一个微波程控信号源的GP -IB标准接口的设计方案，并在微波信号源上得以具体实现。
A design scheme of GP-IB standard interface for microwave program controlled signal source is proposed, and is realized in this microwave signal source.
STA5型用户板用于数字程控交换机的用户接口，也可做为各类接入网系统的远端二线模拟接口。
STA5 subscriber line is applied to subscriber line interface of programmed control digital switches, and two wire analogy remote interface of access network.
测试系统包括程控电源、测试回路、信号采集、调理电路和单片机数据采集接口电路等部分。
This system is composed of a programmable power source, a test circuit, a signal sampler, a signal conditioner and a Single Chip Microcomputer.
设计了该软件各个部分的处理流程、过程控制、数据结构、用户界面和接口等；
This author has designed the processing flow, course-controlling, data structure and user's interface of each components of the software.
新型接口包括有应变放大器和由微机程控的多路自动转换器。
The novel interface equipments consist of a strain-amplifier and a programming multiple channel auto-switcher.
网管系统中很重要的一个部分是计费系统，目前各种制式的程控交换机的计费文件输出方式中使用最广泛的当属Q3接口的FTAM文件传送协议。
The charging system is a very important part of TMN. FTAM protocol of Q3 interface is the most popular protocol used in the charging file output of all the exchanges.
介绍了可编程控制频率合成器接口类型，设计了一种基于PC并口的频率合成器编程控制装置。
This paper introduced the interface modes of programmable synthesizer, and designed a control unit based on PC print port.
重点研究接口电路的硬件组成和如何采用硬件语言VHDL编程控制滑动式指纹传感器以完成高质量的指纹采集工作。
The paper studies the hardware of the interface circuit and how to control the sweep fingerprint sensor to complete the task of high quality fingerprint gathering with hardware language VHDL.
最后，根据不同的车间适用场合，分别介绍了两种制造执行系统和车间过程控制系统的接口方式。
Finally, according to different situations in workshop, two kinds of interface methods between MES and Process Control System were introduced.
由于该网络接口系统不做任何数据解释的透明的传输TDM语音帧，从而可以与原有的程控交换机实现无缝接入。
For this interface unframed mode transparently transports the TDM frame without any attempt at interpreting the data, it seamlessly interfaces to all existing PBX equipment.
系统由程控电源、测试回路、信号采样、调理电路和数据采集接口卡等部分组成。
The system is composed of programmable power, test circuit, signal sampler, signal conditioner and data acquisition card.
远程控制系统的硬件主要由单片机控制电路、USB接口电路、无线收发模块构成。
Hardware of the remote controlling system is mainly composed of Single Chip Microcomputer (SCM) controlling circuit, USB interface circuit and wireless transceiver.
预留远程监测、远程控制模块，风管接口模块，可根据需要选装。
Reserved for remote monitoring, remote control module, the wind pipe interface module can be optional according to need.
对微机接口的虚拟实验进行了探索性工作，提出了一个可编程控制模型。
An initial work in the virtual experiment of computer interface has been done. A programmable control model has been proposed.
硬件部分以针对嵌入式应用的S3C4510B微处理器作为主控制器，利用S3C4510B强大的网络功能和众多外设接口实现对现场设备的远程控制。
The hardware is based on S3C4510B as the main controller, which has powerful Internet function and many interfaces to remote control local equipment.
上位机基于CF接口与下位机进行数据通信，给下位机发送量程控制字、数据采集参数等命令，采用中断方式接收下位机采集过来的数据并进行处理，下位机只完成数据的采集。
Host accesses client's data across CF interface, sends instructions to client such as range select word and DAQ parameter, data are sent to host in interrupt mode and then processed.
该系统中的硬件包括D／A和A／D转换接口、程控增益放大器、多路取样阀门控制接口等；软件包括在线流程分析和常规分析软件。
Hardware interface includes A/D, D/A converters, programmable gain controller and multiplex sampling valve controller. software includes on-line process analysis and normal analysis unit.
LXI规范的提出，从一定程度上统一了设备的通信接口方式，特别是在远程控制上具备其它总线无法比拟的优点。
LXI specification somehow unifies the interface of test equipments. And it gives a great advantage in instruments remote controlling compared with other test bus.
RS-232接口可以与电脑连接， 以实施数据资料记录和远程控制。
RS-232 interface lets you connect to a PC for datalogging and remote control.
同时，该测试仪还设计了用来实现仪器可程控的接口模块。
The tester also features programmable control by using the interfacing module.
它由分布式网络 （INFINET） ，过程控制单元 （PCU） ，操作员接口站 （WSA） ，工程师工作站 （EWS）以及计算机接口单元 （CIU）等组成。
It is made up of distributing network (INFI NET), process control unit(PCU), operator interface station (WSA), engineering work station (EWS) and computer interface unit (CIU).
本文阐述了可编程控制器控制系统中，通过ASCII模块，实现远程操作站与可编程控制器的连接，并开发了ASCII模块中的接口通讯程序。
This paper expounded that the long distance operating station connect to PLC control system with ASCII module, and edited the communication program stored in ASCII module.
应用推荐