围带自锁状态下内弧表面的最大离心应力发生在外拉筋孔截面的拉筋孔靠进汽侧处；
When the blade shroud under the status of self locking, the maximum centrifugal stress of the concave will occurred on the section of outer lace hole and nearby the leading edge.
这种热应力与离心应力、气动应力合成的综合应力可能引起涡轮叶片的低循环疲劳失效。
The synthesis of thermal, centrifugal and aerodynamic stresses may cause the low cycle fatigue failure of the blades.
锥齿轮在高转速下，在槽底的离心应力和振动应力的组合应力是引起齿轮破坏的主要原因。
At high gearing speed the combined stresses of centrifugal load and resonance vibration at the notches are the main cause for the catastrophic failure of the bevel gear.
应用可视化数值模拟方法，借助于大型通用有限元软件ANSYS建立砂轮回转的数学模型，对离心应力进行了仿真研究。
A simulation study was made of the centrifugal stresses exerted on a grinding wheel by means of a visual numerical simulation technique, using the FEM software ANSYS.
用有限元方法计算了铝热离心法制备不锈钢内衬复合钢管过程中的残余热应力分布。
The thermal stress distribution of the stainless steel lined composite steel pipe prepared by centrifugal-SHS process was calculated by the finite element method under thermoelastic assumption.
介绍了应用数值分析和离心模型试验方法对三峡深水高土石围堰进行应力变形研究的成果。
This paper introduces the research results on numerical stress strain analysis and centrifuge model test for the TGPs high soil rock cofferdam.
使用修改移植的MCSAP有限元分析程序对某高速弧齿锥齿轮进行了离心载荷下的变形和应力的分析。
MCSAP program was applied to the finite element analysis for the stress and deformation of a high-speed Gleason spiral bevel gear under centrifugal load.
从应力—应变关系的相似特性出发，找出了小比尺离心模型与原型的相关关系。
The nonlinear similitudes between small models and prototypes are set up according to the similarities of stress-strain relations.
模拟结果与已有实验结果吻合，说明采用雷诺应力湍流模型能准确描述超高速离心叶轮中固体颗粒的运动轨迹。
The conclusions show that Reynolds stress model can be used to describe the tracks of particles in the extra-high speed centrifugal impeller accurately.
通过南昆线膨胀岩路堤离心模型试验，得出路堤在不同状态下的应力与变形特征。
Through the centrifuge modelling tests on expansive rock embankment in Nankun Railway, the characteristics of stress strain under different conditions are obtained.
本文用三维光弹性法分析锥齿轮在扭矩和离心载荷下的应力分布。
The three-dimensional photoelasticity method is used to analyze the stress distribution in the bevel gear under torsional moment and centrifugal load.
本文在有限元应力分析的基础上建立了虹吸离心机转鼓整体优化计算的数学模型，并对实际转鼓进行了优化计算。
In this paper, base on the finite elements stress analysis, the mathematic model of the optimum calculation of siphon peeler centrifuge basket is been built.
对三足离心机转鼓采用有限元方法进行了应力分析，并进行了安全性评定。
This paper presents the stress analysis of three-column centrifuge drum by fi-nite element method, security assessment is also performed.
并对车轮车轴应力分布，飞轮离心力对紧固力过盈量的影响作了论述。
The stress distribution on wheel shaft and the effects of flywheel centrifugal force on its tight fit are discussed as well.
物料离心液压引起的最大应力和最大径向位移都随着转鼓壁厚的减小而增大。
With the decrease of thickness of drum wall, the maximum of stress and radial displacement created by materiel pressure increase.
为确定一种离合器飞轮新产品在大离心力作用下的总体强度储备，对飞轮在离心力场及配合应力作用下的应力分布作有限元分析，并进行了超速破坏试验。
A new type of clutch flywheel needs to determine the limited strength under high centrifugal stress. Finite element analysis and burst spin tests of the flywheels has been done.
介绍了静态水力旋流器压力场的理论分布规律，研究了旋流器内部受到离心力、径向作用力及切应力的情况。
The centrifugal force, radial force and tangential stress inside hydro? _cyclones were analyzed. The process of test technology for pressure field was designed.
用有限元法对具有不同过盈量的加强箍对离心机转鼓内应力的影响进行了分析比较。
An analysis and a comparison was made of the influence of the reinforced hoops with various shrink ranges on the internal stress of a centrifugal drum using the finite element method.
用离心试验法模拟了填埋体的沉降和边坡土工膜的应力应变状态，并将其与有限元计算结果进行了对比。
The settlement of wastes and the stress and strain status of geomembranes on a landfill slope were simulated by centrifugal experiments, and the results were compared with those of FEM calculation.
本文通过离心试验，研究了饱和粘土在考虑土体自重应力作用下的固结变形特性。
Study of the consolidation and deformation characteristics of saturated clay under self-weight by centrifuge model is described.
本文通过离心试验，研究了饱和粘土在考虑土体自重应力作用下的固结变形特性。
Study of the consolidation and deformation characteristics of saturated clay under self-weight by centrifuge model is described.
应用推荐