原装车精准版型，专车专用，在整形外观上不断进行试验，不断的更新改进产品，不卡离合器和刹车挡。
Original precision version, for special car. We continuously test in carpet appearance, constantly updated product, so as to no stuck clutch and brake block.
文章介绍了该离合器的结构、工作原理、试验情况和节能效果。
The paper introduces the structure of such clutches, the working principle, the testing status and the energy saving results.
检查离合器分离是否彻底：将车梯支起，拧放离合器握把，进行换档试验。
Check the clutch is thoroughly: the car ladder teams up, twist, put the clutch wrap shift test.
介绍了作者研制的摩托车离合器性能试验台的工作原理、离合器性能试验的原理和方法、试验台的功能及其实现方法。
The paper describes the development of the tester for motorcycle clutch performance, the mechanism and function. It gives the approach to design and manufacture the tester.
片式离合器是摩托车上的重要部件，不同的摩托车其试验模拟参数也不同。
Plate type clutch is an important part of motorcycle, with different testing analog parameters in different motorcycles.
这些系统还可以用于大马达联轴节、减速器、离合器等的试验。
These systems can also be used in tests of large motor couplings, speed reducers, clutches, etc.
本文介绍了形状记忆弹簧中央驱动式风扇离合器装于发动机的试验结果。
The test results on the centre actuated fan clutch with the shape memory spring set on the engine are presented.
试验台设计采用新型加载装置——磁粉离合器和单板计算机控制，自动化程度较高。
New loading device, magnetic powder clutch and single-board computer control, are employed in tester design with better automation.
作者用测厚法与称重法进行的测量离合器片和刹车片磨损值的对比试验，证明称重法真实可靠。
Weight measurement method is proved reliable through contrast experiments of thickness measurement method and weight measurement method ot test the wear of clutch lining and brake lining.
叉车整车试验表明在叉车上应用膜片弹簧离合器优于螺旋弹簧离合器。
The tests of complete forklift truck shows that using diaphragm spring clutch in forklift truck is better than spiral spring clutch.
在台架上对某一离合器到离合器式自动变速器的控制系统进行了试验研究。
An experimental study on the control system of a clutch-to-clutch type automatic transmission is conducted on test bench.
试验结果表明，该方法不仅简单实用，而且检测与控制效果良好，满足了CVT离合器试验系统的技术要求。
The experimental results show that this method features simply operation and excellent testing and control effect, meeting the technical requirements for CVT clutch testing system.
由于在整个系统中采用了一种新型的车用磁粉离合器，因此本文建立了磁粉离合器模型，并对磁粉离合器的控制规律进行了研究和试验。
Because a new type of magnetic powder clutch for vehicle is employed in this system, the model of it is built up and the control rule is researched.
简要介绍了离合器式螺旋压力机的结构、工作原理和特点，以及主要技术性能和试验。
This article briefly introduces the construction, principle of work and property of clutch operated screw press, and mainly presents its major technical performance and tests.
介绍了一种高速发动机离合器轴承试验机测控系统的组成、工作原理和控制算法。
The composition, working principle and control arithmetic of a high - speed aviation engine clutch bearing test machine is introduced.
汽车离合器从动盘总成扭转性能检验机是汽车零部件试验的重要试验设备。
A new torsion testing machine for driven plates of automobile clutch, which is important testing equipment in automobile component industry, has been presented in this paper.
汽车离合器从动盘总成扭转耐久试验机是汽车零部件寿命试验的重要试验设备。
A new torsion durability-testing machine for driven plates of automobile clutch, which is important testing equipment in automobile component industry, has been presented in this paper.
建立了描述湿式离合器结合过程的多状态动力学模型，通过台架试验验证了模型的正确性。
A multimode dynamic model of a wet clutch in engagement process was developed and its correctness was verified by the experiment.
为确定一种离合器飞轮新产品在大离心力作用下的总体强度储备，对飞轮在离心力场及配合应力作用下的应力分布作有限元分析，并进行了超速破坏试验。
A new type of clutch flywheel needs to determine the limited strength under high centrifugal stress. Finite element analysis and burst spin tests of the flywheels has been done.
试验结果表明，该测试系统可有效地对离合器进行实车试验，测试精度高，满足了车载便携测量的要求。
The test results show that the test system can effectively test on-board clutch performance with high test accuracy and it can meet the requirements of on-board portable measurement.
提出了电机高速电磁离合器的几种控制电路，并进行试验分析。
Some new types of control circuits of high speed electromagnetic clutch used in electrical machine are designed in this paper.
本文简介桑塔纳轿车离合器耐久试验过程和其结构参数，分析桑塔纳离合器的性能及一些故障产生的可能原因。
The durability test procedure and its structural parameter of Santana clutch are briefly introduced. The performance and fault of Santana clutch are analyzed in this paper.
研制旋转轴向式起动机单向离合器性能测试系统，能够在对其进行性能试验，检验其性能参数是否满足标准规定的技术条件，更好地满足日益提高的市场需求。
Therefore the research into the test bed of the rotation SOC, which can testify whether the clutch meets the standard technique, satisfies the market's increasingly demands.
采用试验和有限元的方法研究了离合器从动盘结构的刚度和强度，并对应力集中的区域提出了改进方案。
The stiffness and strength of clutch driven plate assembly were experimentally and numerically studied, an improvement design on the stress concentration was given.
装机试验表明，所研制摩擦片磨损总量最小，耐磨性能和使用寿命在正常使用或离合器打滑情况下优于石棉摩擦片。
Test show that wear loss of developed friction disk is less, anti - abrasion properties and employment lifespan is superior to that of asbestos friction disk either in normal or sliding case.
其次，设计搭建了磁流变液离合器性能测试试验台，并进行了测试实验结果的研究分析。
Secondly, the experiment table of MRF clutch was designed and constructed, and the test results were analyze.
试验结果表明，换挡过程中通过控制断油电磁阀和设置换挡重叠并与离合器的接合过程相协调，可显著提高AMT的换挡品质。
The test results show that by controlling the fuel cutoff solenoid, coordinated with clutch engagement, the shift quality of AMT can be dramatically improved, while starting shift operation…
其特点是运用差动运动原理，使试验转速可以达到轻型车离合器较高的起步转速，以较好地模拟离合器的实际工作情况。
For well simulating the real working conditions, the differential kinematics is used to get a higher start rotating speed of clutch of the light mobile.
要反复调整反复试验，直到确认达到最满意，首先，将传动轴安装上，将主离合器拉杆连接上。
Repeated trial and error to adjust until the confirmation to achieve the most satisfaction First, install the drive shaft, Will connect the main clutch lever.
要反复调整反复试验，直到确认达到最满意，首先，将传动轴安装上，将主离合器拉杆连接上。
Repeated trial and error to adjust until the confirmation to achieve the most satisfaction First, install the drive shaft, Will connect the main clutch lever.
应用推荐