通过正交试验证明加工时间是影响去除量的主要因素，而磨料粒度对表面粗糙度影响较大。
Orthogonal experiment shows that the time is the main factor of removal rate and abrasive granularity is the crucial factor of surface roughness.
抛光加工与磨削加工方式基本相同，所不同之处是抛光加工所采用的磨料粒度比磨削要细得多，抛光速度也大。
Polishing and grinding the same way, the difference is polishing the abrasive particle size used to be much thinner than the grinding, polishing speed is also large.
填料粒度和磨料粒度都对涂层的气固冲蚀磨损有影响，但在给定的试验条件下，填料粒度对涂层的浆体冲蚀磨损影响甚微。
The sizes of filler and abrasive have influence on the solid particle erosion of coating under the given condition, the size of filler be of weak influence on the slurry erosion.
并分析了压力、靶距、横移速度、磨料供给量、水流量、磨料粒度和磨料种类对除锈效率的影响，为磨料浆液除锈各参数的选择提供了参考。
The effects of water pressure, off distance, transverse speed, abrasive flow rate, abrasive grade and the kind of abradant to the effectiveness of rust -removing are analyzed.
砂轮的主要特征包括磨料、粒度、硬度、组织个结合剂五个因素。
The main characteristics of abrasive wheels include five factors, namely abrasive material, grain size, hardness, structure and bond type.
当磨料的添加量和粒度增加时摩擦系数增大。
Friction coefficient increased with abrasive size and concentration increased.
白刚玉段砂、粒度砂、细粉、微粉在耐火材料、磨料磨具等不同行业具有广泛的用途。
White fused alumina products including section sand, grain-size sand; fine powder and micro powder are widely used in refractories, abrasives and other industries.
配制四种不同的胶粘涂层，通过改变磨料的粒度和磨损行程对其进行磨粒磨损性能测试。
In this paper, four kinds of epoxy bond coating were obtained, the character of grain abrasion with alter particle's size and wear distance were researched.
模型采用三层结构，输入变量有水射流压力、水喷嘴直径、磨料粒子粒度(直径)、磨料流量和切割头进给速度。
Three layers network topology is adopted. The input variables are water pressure, diameter of orifice, diameter of abrasive particles, flow rate of abrasive and feed rate of cutting head respectively.
研究结果表明：晶种的加入能有效地促进刚玉磨料的烧结，细化晶粒，使晶粒粒度分布范围较窄；
The results indicated that the introduction of crystal seed was effective to promote the sintering of new ceramic corundum abrasive and decrease its crystal size;
属于磨粒对加工效果影响的因素有：磨料的导磁率、粒度、配比、磨料的填充量等参数。
The factors that belong to abrasive are the permeability of abrasive, grain size, materials matching ratio, the amount of the Abrasive and etc.
属于磨粒对加工效果影响的因素有：磨料的导磁率、粒度、配比、磨料的填充量等参数。
The factors that belong to abrasive are the permeability of abrasive, grain size, materials matching ratio, the amount of the Abrasive and etc.
应用推荐