研究证明，该试验机能模拟疏浚工况，已成功应用在挖泥船泥泵壳和绞刀片耐磨材料的磨损试验上。
The developed materials through the sand slurry abrasion test have been successfully put into practice in the shell of dredging pump and the cutter piece.
通过磨损试验研究了变形对低合金耐磨铸铁耐磨性的影响。
The abrasiveness of white cast iron with low alloy content was studied through abrasion test.
利用电子探针、磨损试验机等试验手段，研究了微量元素对特殊黄铜的组织和耐磨性能的影响。
Effect of microelement on the microstructure and wear resistance property of special brass have been investigated by SEM, abrasion machine etc.
本试验结果还说明，在一些磨损条件下，高速钢中一次碳化物对耐磨性的影响不是主要的，基体性能可以起到更大的作用。
It may also be inferred that under certain wear conditions, it is not primary carbides but matrix properties which play major role in the wear resistance of HSS.
装机试验表明，所研制摩擦片磨损总量最小，耐磨性能和使用寿命在正常使用或离合器打滑情况下优于石棉摩擦片。
Test show that wear loss of developed friction disk is less, anti - abrasion properties and employment lifespan is superior to that of asbestos friction disk either in normal or sliding case.
利用自制冲蚀磨损试验装置，研究了耐磨胶粘涂层气固冲蚀磨损的特性。
The abrasion properties of wear-resistant adhesive coatings have been studied on self-created abrasion test facility.
对不同载荷作用下的高铬铸铁在耐磨实验机上进行了磨料磨损试验；
The high chromium white cast iron was carried on wear abrasion test under different loads on the testing machine.
定性研究主要是对该材料耐磨损性能的影响因素、磨损失效形式、磨损机理进行试验研究和接触分析。
The qualitative study mainly includes experimental researches on influencing factors of wear resistance, failure types and mechanisms of the wear of the material and contact analysis.
在动载三体磨粒磨损条件下，试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
采用磨损对比试验，研究了激冷层中不同石墨含量激冷铸铁凸轮之间的耐磨性关系。
The wear resistance of chilled cast iron cams with different graphite contents in the chilled layer were studied through wear contrast test.
本文通过焊接试验、显微分析和磨损试验论述了以铬、镍、铁基合金代替钴、铬、钨合金作石油钻头牙爪堆焊耐磨合金的问题。
In this article we discussed the possibility of replacement of cobalt alloy by Cr-Ni iron Base alloy in drill bit bearing on the basis of welding test, wearing test and microscopic examination.
鞋。外鞋帮的试验方法。耐磨损性。
研究水平连续铸造方式下高磷含硼铸铁中磷共晶和硼化物的分布特点，并进行超耐磨性试验，对磨损试验后材料的微观形貌进行试验验证分析。
Study metallographic structure of phosphor eutectic and boride in continuous cast iron. The microstructure of piston has been analyzed and proved after wear test.
通过快速模拟磨损试验发现铌铸铁油环耐磨性能比铬钼铜油环提高87.3%，并降低了油环的制造成本。
The results also find that wear resistance of niobium cast iron oil ring is 87.3% higher than that of CrMoCu alloy cast iron along with the cost reduction for niobium cast iron oil ring.
利用试验优化技术设计试验方案，采用激光图形雕刻加工的手段实现齿轮表面仿生非光滑形态，研究非光滑与光滑两种形态齿轮的耐磨损性能。
Using optimum design for experiment scheme, laser graphic texturing was adopted to form bionic non-smooth microstructure on the gear surface to study anti-wear capability of the gears.
通过销盘的磨损对比试验，对进行了磁化处理的与未作磁化处理的高速钢材料作了耐磨损性能的研究。
The wear of the unmagnetized and magnetized high speed steel material are compared in the wear between pin and disk text.
应用对滚圆盘磨损试验机研究了合金铸铁经激光熔融处理后的耐磨性，试验结果指出，激光处理试样的磨损失重大为减少。
The roll disk wearing testing machine is used to study the wearability of alloy cast iron after laser melting. The test result shows that the wear weightlessness is reduced greatly.
用微观组织分析、杆盘式磨损、湿磨法磨损和冲击韧性等试验手段，对高铬铸铁衬板的显微组织、力学性能和耐磨性进行了试验分析。
Failure analysis of high chromium cast iron liner has been studied by the microstructure, pole-pan wear abrasion, wet grinding and impact toughness.
结果表明，在中、低冲击磨料磨损条件下，试验钢的耐磨性优于中碳低合金耐磨钢和高锰钢。
Under lower and medium impact energy, the abrasive wear resistant performance of the steel metioned is higher than that of low alloyed medium carbon wear resistant steel and high manganese cast steel.
通过落球冲击和滑动磨损试验探讨了冲击对高铬铸铁和奥氏体不锈钢耐磨性的影响。
Effect of impact on wear resistance of high chromium cast iron and austenitic stainless steel has been studied by ball-on-ball impact and pin-on-disc abrasion test.
通过对M L-100磨粒磨损试验机测试，发现环氧树脂涂层的耐磨性与陶瓷粉末的粒度与含量有密切关系。
Wear resistance tests have proved that the wearability of epoxy. Bonding coating is firmly connected with the size and weight of ceramic powders.
通过对M L-100磨粒磨损试验机测试，发现环氧树脂涂层的耐磨性与陶瓷粉末的粒度与含量有密切关系。
Wear resistance tests have proved that the wearability of epoxy. Bonding coating is firmly connected with the size and weight of ceramic powders.
应用推荐