结果证明多数粘度指数改进剂可提高油性极压剂的综合磨损值。
It is proved that most kinds of polymer additives can improve the composite wear value of oiliness and EP agent.
作者用测厚法与称重法进行的测量离合器片和刹车片磨损值的对比试验，证明称重法真实可靠。
Weight measurement method is proved reliable through contrast experiments of thickness measurement method and weight measurement method ot test the wear of clutch lining and brake lining.
结果表明，通过人工神经网络估算刀磨损值与实测值基本一致，系统取得了90%的刀具磨损识别成功率。
The results from the system are largely consistent with the recorded data by instruments. This system suggests that its reliablity be up to 90 percent.
汽车离合器在实际使用过程中，希望能预测出一定条件下工作的零件的磨损值，以便于控制零件的磨损和制订合理的维修期限。
It is expected that the wear value of automotive clutch part used in certain condition can be predicted to control the part wear and determine the reasonable maintenance and repair time.
通过比较实时采集的切削力与不同刀具磨损值对应的切削力大小，可确定刀具的磨损状态，并利用建立的简化模型计算刀具的精确磨损值。
The mapping relationship between machining parameters and cutting forces in different tool wear states was built up by means of B-spline neural network in this new methodology model.
磨损。吊钩截面周长或承载销超过磨损超过10%（或厂家推荐值）。
Wear. Any wear exceeding 10% (or as recommended by the manufacturer) of the original section dimension of the hook or its load pin.
当其余各影响参数保持一定值时，磨损率随接触面积的增大而增大。
While giving other parameters, wear rate increases along with the increase of contact area.
表面粗糙度有一个最佳值，在这个表面粗糙度下电弧能量最小、质量磨损率也最小。
There is an optimum surface roughness which will produce minimal arc energy and minimal wear rate.
一旦传感器输出偏离最初预期阀瓣末端位置值时，用户就可以立即检测到磨损密封件。
The user can thus detect a worn seal as soon as the sensor outputs a value that deviates from the originally expected flap end position.
但厚度增加到一定值时，磨损速率不变。
When thickness increases above a certain value, wear rate becomes unchanged.
针对异型螺杆铣削加工，采用振动信号特征值作为检测刀具磨损的参量。
The characteristic values of vibration signals were used as testing parameters of tool wear for milling special shaped spiral rods.
从混凝土磨蚀和力学性能试验得知，水工混凝土的磨蚀程度依赖于混凝土的初始磨损率，抗拉强度和极限拉伸变形值。
Abrasion and mechanical properties test of concrete have shown that the degree of abrasion dependent on initial abrasion ratio, flexural strength and limit strain.
当承击砧磨损严重，难以调整到设计值时，只需更换承击砧而不必更换大质量的承击梁。
When worn anvil bearing strike, difficult to adjust to the design value, only need to change when bearing strike without replacing large quality anvil bearing strike beam.
本文对ASTMD 4172精密度值和时设备的要求提供了异议。对继续引进磨损四球机持否定态度。
It raises an objection against ASTM D 4172 precision value and equipment requirement, and adopts an attitude of negating to constantly import four-ball wear tester.
涂层在较大的P、V值范围内与各类配副均具有极低的摩擦系数和磨损量以及很高的尺寸稳定性；长期工作过程中，涂层未出现任何破坏现象。
Under a wide range of P and V value, there are very low friction coefficient and wear, high dimensional stability for coating-metal pairs and no any damage during the test of nylon coating.
涂层在较大的P、V值范围内与各类配副均具有极低的摩擦系数和磨损量以及很高的尺寸稳定性；长期工作过程中，涂层未出现任何破坏现象。
Under a wide range of P and V value, there are very low friction coefficient and wear, high dimensional stability for coating-metal pairs and no any damage during the test of nylon coating.
应用推荐