补偿器包括控制为输出选择哪个写时钟相位的相位旋转器。
The compensator includes a phase rotator that controls which write clock phase is selected for output.
确保所有输入输出电缆线路设置正确，并检查输入相位旋转。
Make sure all the input and output cabling has been performed correctly and check the input phase rotation.
在接收机处，确定所接收的数据流的相位旋转以去除残留频率误差或者估算相位噪声。
At a receiver, a phase rotation of the received data stream is determined to remove a residual frequency error or to estimate the phase noise.
测试结果表明，接收数据的相位旋转得到很好的补偿，性能达到实际系统的设计要求。
The results indicate that the receiving data of various modulation after equalized are ideal, to meet the actual system design requirements.
对倾斜的和水平的四元阵按相位旋转方式激励时的辐射场进行了计算、示出一些典型辐射图。
Computations are performed for radiation field of inclined and horizontal four-element array with turnstile excitation, and some typical patterns are shown.
该算法在传统的基于块状导频的Ls信道估计算法的基础上，加入了相位跟踪算法，补偿了由残余频偏带来的相位旋转。
This algorithm combines the block Pilot-aided LS channel estimation algorithm with a phase tracking algorithm, which can compensate the phase rotation caused by the residual carrier frequency offset.
这允许图形对象的相位差和旋转。
工作在调相状态下的旋转变压器可以用其相位模拟恒星时与赤经、时角的关系。
Phase modulated resolvers can be used to model the relation between the sidereal time right ascension and the hour angle.
该方法同时旋转多个天线单元的信号源的相位，能够使被测信号的起伏显著增加。
This method synchronously rotates the sources 'phases of more than one antenna element, and makes the signal vary more significantly.
这种方法对高斯噪声和星座图由于信号初始相位而引入的旋转具有良好的稳健性，并避免了神经网络中的过学习和局部极小点等缺陷。
This method is robust to Gaussian noise and constellation rotation due to initial phase of signal and avoids overfitting and local minimum in neural networks.
相位信息在旋转机械的振动监测与故障诊断中起着重要的作用。
Frequency information plays an important role in vibration monitoring and fault diagnosis of rotating machinery.
将待处理图像去旋转后，再采用2D相位相关来得到平移参数。
After de-rotation, the traditional 2D phase correlation was imported to get the translation.
在旋转电弧信号的频域分析中，其特征谐波的相位反映了焊缝方向与焊接方向的初始夹角。
In frequency analysis of rotating arc signal, the phase of harmonic characteristic reflects the initial Angle between weld direction and seam's direction.
分析了多雷达信号融合中的幅度相位模型，并基于旋转不变技术提出一种新的幅度相位补偿参数估计方法。
The amplitude-phase compensation model of multi-band radar signal fusion is analyzed and the new amplitude-phase compensation algorithm based on the ESPRIT is presented.
文章研究了自旋为1的粒子在旋转磁场中的几何相位和动力学相位。
The geometric and dynamic phase for spin-1 particle in a rotating magnetic field are studied.
分析了弹道相机系统的构成，并对弹道相机的最主要部分——旋转快门相位控制器工作原理进行剖析。
The composition of trajectory camera and working principle of the phase controller of revolution shutter are analyzed.
相位相关作为一种图像匹配技术对噪声有较高的容忍程度，检测结果与照度无关，受几何失真影响小。但该方法对旋转变化非常敏感。
Phase correlation algorithm as a kind of image matching method has many advantages such as insensitive to noise, unrelated to illumination of target, immune to geometric distortion.
作者还认为，常规式抽油机的曲柄旋转方向应规定为逆时针，并建议研制可调相位角的曲柄平衡重。
The author holds further that the crank pin rotation on conventional pumping units should be assigned in counterclockwise...
仿真及对柔性转子试验台振动信号的分析结果表明，基于频谱细化和相位差校正的全息谱能有效提高其分析精度，更加精确有效地诊断旋转机械的故障。
With correction of phase difference for the max peak, the amplitude and phase of each order frequency can be acquired. At last, the holospectrum was synthesized.
通过对旋转机械相位信息的研究，提出从倍频相位中提取相对时相作为诊断特征量。
In the research of phase information of rotary mechanism, comparatively phase is extracted from multiple frequency phase as diagnosing feature.
此方法减小了相位离散值引起的量子化噪音，它适用于制作一切球面和非球面的具有旋转轴对称的相息图。
The method reduces the noise caused by discrete phase on reconstructing imago. This method can apply to either spherical or aspherical kind of Kinoform with axial rotating symmetry.
计算机模拟的结果表明，这种滤波法对输入信号的旋转变化和尺度缩放变化，相对于传统的匹配滤波法及仅相位滤波法要敏感得多。
Computer simulations show that this kind of filter is much more sensitive as compared to a matched spatial filter or a phase-only one.
转子的旋转运动和线性输出信号，围绕出厂预置的零位移动60(总共120)度。此输出信号的相位指示离开零位的位移方向。
Rotational movement of the rotor shaft results in a linear output signal that shifts 60 (120 total) degrees around a factory preset null position.
转子的旋转运动和线性输出信号，围绕出厂预置的零位移动60(总共120)度。此输出信号的相位指示离开零位的位移方向。
Rotational movement of the rotor shaft results in a linear output signal that shifts 60 (120 total) degrees around a factory preset null position.
应用推荐