轿车上的直齿圆锥齿轮尺寸精度与产品质量要求很高，难以采用常规的塑性加工技术成形。
Straight bevel gears used in car differential have strict requirements for dimensional precision and quality, it is difficult to form accurately them by the traditional forging techniques.
本文以直齿锥齿轮为例，给出了直齿锥齿轮的设计导航流程，提出在已经标准化了的齿轮零件库中匹配出最相似的齿轮零件是关键的步骤。
Taking cone gear as example, this paper presents the design guidance of cone gear and emphasizes that it is the key step to match the most similar gear in standardized gear parts base.
在应用边界元方法计算直齿圆柱齿轮的本体温度场的基础上，进一步研究了直齿轮在齿厚方向和沿其轴向由其本体温度的改变和传动载荷而引起的热弹性变形。
On the basis of this result further study is made on thermal elastic deformation resulted from bulk temperatures changing and transmission load of the spurs gear in the direction of tooth and axle.
介绍了渐开线直齿内齿轮插齿刀的优化设计方法。
The optimum design method of involute internal gear slotting cutter is introduced.
直齿锥齿轮的齿圈径向跳动是重要的检验项目，是影响齿距累积误差和齿距误差的重要因素。
The radial runout of tooth ring of the coniflex gear, which is an important test item, is an important factor influencing the accumulated error of tooth spacing and the error of tooth spacing.
其次，用有限元法，计算了直齿圆柱齿轮传动的啮合刚度，得出了啮合刚度的变化曲线。
Secondly, on the base of FEM, mesh stiffness of straight tooth cylindrical gear is calculated, and curve of stiffness is find.
利用直齿齿轮泵的困油容积变化公式，求出了斜齿齿轮泵的困油容积变化公式，得到了斜齿齿轮泵不发生困油的螺旋角。
According to the volume oil formula of the straight gear pump, the volume oil formula of the helical gear pump is got and the helix Angle no trapping is found.
在采用液体静压和液体动压轴承的柔性轴的高精度单级直齿和斜齿减速器上已经过实验论证。
Experiments have been conducted on a high-precision single stage spur and helical gear reducer with flexible shafts mounted on hydrostatic or hydrodynamic bearings.
修形直齿轮因误差因素在齿对的啮入和啮出位置会出现啮合干涉或啮合间隙。
Errors of modified spur gears results in meshing interference or meshing clearance at the position of mating teeth coming into or out of contact.
直肠癌是指齿线至直——乙状结肠交界处之间的癌肿，是消化道最常见的恶性肿瘤之一。
Cancer refers to the teeth straight line-at the junction between the sigmoid colon cancer, digestive tract is one of the most common malignant tumor.
本文以汽车系列化零件中比较有代表性的直齿锥齿轮为例，详细论述了该系统的整个开发过程。
This article regards representative straight bevel gear as a example in automobile series parts and detailedly states the total exploitation process.
对直齿圆柱齿轮传动进行模糊可靠性优化设计，设计出的方案更经济、合理、适用。
The plan carrying on the fuzzy reliability optimization design to the spur gear drive will be more economical, reasonable and suitable.
推导基于工程应用的直齿圆锥齿轮啮合面的数学模型。
The inferential reasoning based on the mathematical model of straight bevel gear mating surface in project application.
本文从尖角铣刀割圆出发，拟出了一套钻头牙轮直铣齿的计算公式。
A set of calculating formulae for vertical milling teeth of drilling bit cones is derived herein from cutting rows with Angle cutters.
建立了精确计算直齿锥齿轮轮体积以及沿齿长方向各截面面积的数学模型；
The mathematical pattern for accurately calculating volume of tooth and areas of each section which is dispersed along the length of tooth is established.
详细介绍了实际工作中较实用的直齿渐开线齿轮、斜齿渐开线齿轮参数的测量与确定方法。
This paper introduces in detail some measuring and determining methods of the parameters of the straight and inclined involute gears that are more practical in the actual work.
介绍了在Y 54插齿机上采用对数分齿计算方法加工大质数直齿轮的计算方法和计算实例。
In this paper introduce the calculation method and example of processing the big prime number straight gear apply the method for calculating the logarithm dispart tooth in Y54 gear shaper.
对直齿面齿轮传动在考虑边缘接触下的承载接触进行了分析。
The loaded tooth contact ana-lysis(LTCA) under the condition of tooth edge contact is investigated in this paper.
直齿锥齿轮一般要在专用机床上加工，但能够加工大型直齿锥齿轮的生产企业极少。
The straight subulate gears are commonly been machining on special machine tool, but the factories of machining the large-size straight subulate gears are rather less.
将此高精度直齿外珩轮应用于珩齿试验中，被加工齿轮的齿形误差和表面光洁度得到了极大地提高。
The honing experiment shows that the teeth error and surface roughness of the machined gear have been improved greatly.
介绍了两级直齿圆锥—斜齿圆柱齿轮减速器等强度优化设计的数学模型及优化方法的选取。
In this paper, a mathematical model and the selection of optimization method for equal strength optimized design of two-stage straight bevel gear-helical cylindrical gear reducer are introduced.
实验结果表明，弯矩与转角之间明显存在着迟滞现象，对于直齿联轴器而言，二者之间是非线性的关系；
The relationship between the moment and its angular displacement is obtained, and the hysteresis exists clearly in the test.
建立了单级2k - H直齿行星传动的纯扭转集中参数动力学模型。
A simplified purely torsional concentrated parameter model of a single stage 2k-h spur planetary gear transmission (PGT) is developed.
建立了直齿圆柱齿轮、齿圆柱齿轮、齿圆锥齿轮、齿圆锥齿轮的统一模型。
A unified model was established for spur cylindrical gears, helical cylindrical gears, spur bevel gears and helical bevel gears.
研究了直齿圆柱齿轮的冷精锻过程，分析了分流孔形状、成形工艺等因素对齿轮成形的影响。
The cold precision forging of spur gears has been researched, and the effects of relief-hole shape and forging process on the spur gears forming has been analyzed.
互相啮合的直齿圆柱齿轮，必须具有相同的径节。
安装在两根平行轴上的直齿轮最常见的齿轮，这种齿轮带直齿。
A pair of spur gears for mounting on parallel shafts are the most common type of gears, which have straight teeth.
静态计算结果表明，直齿锥齿轮齿廓长修形具有较好的减振效果。
The result of static calculation showed that the tooth profile long modification of spur bevel gear possesses better effects of vibration reduction.
插齿刀CAD系统一直是机械加工企业的攻关课题。
The development of Gear Shaper Cutter (GSC) CAD system has been a project in the machinery manufacturing corp.
插齿刀CAD系统一直是机械加工企业的攻关课题。
The development of Gear Shaper Cutter (GSC) CAD system has been a project in the machinery manufacturing corp.
应用推荐