本文介绍IGBT、EXB841和LEM模块在大功率PW M直流伺服驱动系统中的应用和系统抗干扰设计。
This paper introduces the application of IGBT, EXB841 and LEM models in high power PWM DC servo driving system, and the EMCD of driving system.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Adopting ac servo motor as the driving device, can the dc servo motor and a high precision, high performance as the half closed loop or closed loop control system.
本文分别用PI控制器和IP控制器对直流伺服电机模型建立PWM驱动数字型调速系统。
The numeral timing systems driven by PWM are set up for the direct current servo motor model by using the PI. and IP contrail ers respectively.
利用PWM驱动方式控制电机的转动，并设计出了直流伺服控制系统硬件电路图。
Using PWM to drive motor, and we design a circuit in DC serve control system.
本系统由80C196KB／KC单片机、27C64存贮器、光学编码器及外部译码电路、电机驱动电路、限流电路、直流伺服电机等组成。
The system consists of 80C196KB/KC single chip microcomputer, 27C64 memory, optical coder and its external decode circuit, motor drive circuit, current - limiting circuit, DC servo motor etc.
双电机同步直流伺服系统是颤振激励系统的驱动单元，控制器作为伺服系统的核心，对整个系统性能的优劣起着非常重要的作用。
DC servo system is the drive unit of vibration stimulation system. As the core of servo system, undoubtedly controller plays an important role to the whole system performance.
在伺服系统中要使系统能够满足所期望的性能，伺服系统驱动器直流母线电压的选择尤为重要。
To make the servo system have the expected its, it s especially important for selection of DC bus voltage in servo driver.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Adopting ac servo motor as a drive device, can and dc servo motor as a high precision, high performance and a half closed loop or closed loop control system.
双电机直流同步伺服系统是颤振激励系统的驱动单元，控制器作为伺服系统的核心，对整个系统性能的优劣起着非常重要的作用。
Double motors DC servo system is the drive unit of flutter exciter system. As the core of servo system, controller plays an important role to the whole system performance.
在无刷直流电动机驱动的雷达伺服系统中，采用了智能功率驱动模块(IPM)来实现功率驱动，它能够满足苛刻的环境要求，并能获得比较满意的系统性能。
Intelligent Power IC (IPM) is applied to a radar servo system, which is drived by brushless DC motor. The system can be used in harsh circumstances and get some satisfactory performance.
该系统采用永磁式直流伺服电机为驱动源驱动撕带轴的转动，向包装机构供给撕带。
The permanent magnetic servo DC motor is used as the driving source of making the axis of the tear tape rotate to feed the packing mechanism with the tear tape.
该控制系统以无刷直流电动机为伺服驱动装置，以微型计算机为处理器。
The control system use BLDC motor as servo device, take microcomputer as the processor.
通过一个以直流伺服电机驱动的半闭环数控系统的实验分析，表明比传统的计算结果有更 高的精度和 可靠性。
The experimental analysis of semi-closed cycle numerical control system driven by direct current servomotor shows that it is more precise than the traditional calculation result.
驱动系统采用脉宽调制直流伺服系统。
The driving system use DC servo system of modulating pulse width.
驱动系统采用脉宽调制直流伺服系统。
The driving system use DC servo system of modulating pulse width.
应用推荐