最后还建立了犁沟效应和疲劳磨损模型。
At last, models for the explaination of fatigue and ploughing wearing are presented.
粘附磨损和疲劳磨损是轨钢的主要磨损形式。
Adhesive wear and surface - fatigue wear are the two major wear forms in rail steel.
齿轮表面的疲劳磨损是齿轮故障的主要形式之一。
Fatigue wear on the surface of gear is one of the main kinds of failure of the gear.
认为其机制主要是：凿削式磨粒磨损和疲劳磨损。
It is concluded that the mechanisms include gouging abrasion and fatigue wear.
而钢领失效的决定性因素是粘着磨损和疲劳磨损。
Bat a decisive factors of ring failure are the adhesive wear and fatigue wear.
表面纳米化有助于减弱低碳钢表面的疲劳磨损效应。
Surface nanocrystallization helps weaken the fatigue wear effect of low carbon steel.
磨损机理主要是粘结磨损、扩散磨损以及疲劳磨损。
The main wear mechanisms are adhesion, diffusion and fatigue.
利用接触疲劳磨损理论讨论激光熔覆试样的疲劳磨损寿命问题。
This paper discusses wear life of laser cladding samples with the aid of the theory of contact fatigue wear.
纳米复合镀层的磨损机制以疲劳磨损为主，而纯镍镀层以粘着磨损为主。
The wear mechanism of the nano-composite coatings were mainly fatigue wear and that of the pure nickel coating was mainly adhesion wear.
形圈链条中销轴和套筒的磨损主要以疲劳磨损为主，并伴随着粘着磨损；
The bushes and bearing pins of the rubber O ring roller chains were characterized by stress fatigue wear and adhesion wear;
操作画面是选用感应式结构，既没有疲劳磨损，使用寿命又比传统按钮长。
Operation of frame structure is the choice of sensor does not fatigue and wear, longer service life than traditional buttons.
纳米管层的磨损机理主要为磨粒磨损、疲劳磨损、粘着磨损和氧化腐蚀磨损。
The wear mechanism of the nanotube layers involved abrasive wear, fatigue wear, adhesive wear and oxidative wear.
磨损有五种磨损形式：磨料磨损、冲蚀磨损、粘着磨损、疲劳磨损和腐蚀磨损。
There are five forms of wear and wear: abrasive wear, erosive wear, adhesive wear, fatigue wear and corrosive wear.
研究了石英和煤两种磨料条件下材料的冲击磨料磨损耐磨性及其疲劳磨损机制。
The impact abrasive wear resistance of materials and its fatigue wear mechanism under the conditions of quartz and coal as abrasive had been investigated.
低速制动下的磨损机理主要为疲劳磨损，高速制动时主要为磨粒磨损和氧化磨损。
With the brake speed of the lower one it mainly refers to fatigue wear, while of higher one it mainly refers to abradant and oxidation wear.
低载荷下的磨损机制以疲劳磨损为主 ，高载荷下的磨损机制主要表现为粘着磨损。
The main wear mechanism of MoSi 2 material is fatigue wear under the lower loads, while adhesive wear is the main mechanism under the higher loads.
本文主要针对陶瓷材料磨削表面残余应力对疲劳磨损和表面硬度的影响进行实验研究。
Effect of surface residual stresses by ceramic grinding on fatigue wear property has been researched by experiment.
系统中的链条出现的氧化点蚀、犁沟磨损及疲劳磨损等特征是系统中磨损的主要机制；
The wear and tear mechanisms of the timing chain system are oxidation erode, furrow, fatigue wear and tear.
该材料低速制动下的磨损机理主要为疲劳磨损，高速制动时主要为磨粒磨损和氧化磨损。
In lowly brake speed it mainly refers to fatigue wear, while in highly brake speed it mainly refers to abrasive and oxidation wear.
对受高温磨损破坏的导卫板进行了失效分析，认为导卫板主要受到了疲劳磨损和磨料磨损。
The guide piece, which was worn seriously under high temperature, was analyzed. It is show that the wear mechanism of guide piece is fatigue wear and abrasive wear.
试验得出，残余奥氏体可阻止疲劳裂纹的萌生和扩展，提高冲击疲劳抗力，降低冲击疲劳磨损。
It is indicated that retained austenite in microstructure can inhibit the initiation and propagation of fatigue crack, improve the resistance to impact fatigue and decrease impact fatigue wear.
高钒高速钢干滑动磨损机理为显微切削和疲劳磨损的复合，并且有应力作用下碳化物的碎裂及脱落。
The wear mechanism of high vanadium high-speed steel is combined micro-cutting and fatigue wear with carbide particle breaking and peeling off under stress.
聚晶金刚石刀具在加工过程中的磨损机理主要表现为具有疲劳磨损特征的沿晶断裂及局部解理断裂。
The cutting tool was characterized by intercrystalline fracture attributed to fatigue and partial cleavage fracture in the machining process.
涂层表面的磨损机制主要为开始以黏着磨损和氧化磨损为主，逐步过渡到以表面疲劳磨损和磨粒磨损为主。
The wear mechanisms of the high temperature of the coatings are mounting and oxidation early, fatigue and abrasive afterwards.
磨损面上存在大量的擦伤现象，铁基合金涂层室温和高温下的主要磨损机制是以剥层形式出现的应变疲劳磨损。
The scuffing phenomenon on worn surface indicated that the main wear mechanism of the coating at room and high temperature w...
腐蚀环境对材料的裂纹扩展有较明显的加速作用，酸碱处理后材料的磨损机制主要是磨粒磨损和疲劳磨损的综合作用。
The corrosive environment accelerates strongly crack growth of the composites. After acid and alkali treatment, the wear mechanism is the synthetic action of abrasive wear and fatigue fracture.
磨料磨损、疲劳磨损和胶合等是引起石油钻机传动链条磨损超限，承载；能力降低，最后导致链条断裂破坏的主要原因。
The abrasive wear, fatigue wear and adhesive wear are the main factors causing the excess wear and breaking of the driving chain on drilling RIGS.
骨水泥在小牛血清介质中微动磨损的损伤机制主要为黏着磨损和疲劳磨损，溶液分子在应力作用下对骨水泥基体有削弱作用。
In calf serum medium, the wear mechanism of fretting is mainly adhesive wear, fatigue wear and the weakening effect of solution molecules on the bone cement matrix under stress.
当轮胎逐渐磨损、钢丝层渐渐疲劳、胎面老化之时，它的性能也必然减弱。
When the tyre wear, wire layer gradually fatigue and tread aging, it will weaken the performance.
当轮胎逐渐磨损、钢丝层渐渐疲劳、胎面老化之时，它的性能也必然减弱。
When the tyre wear, wire layer gradually fatigue and tread aging, it will weaken the performance.
应用推荐