受灯泡的时间常数限制，本电路只能低频工作。
This circuit is restricted to low frequency operation by the lamp time constant.
本方法通过观察水模样品的磁共振信号的变化来调正补偿电路的时间常数和增益。
The method adjusts time constant and gain of compensation-circuits with determining change of magnetic resonance signal of phantom.
本文在分析LR电路过渡过程的基础上，讨论了以特定激励源实现变压器绕组电阻零时间常数测量的方法。
On basis of LR circuit transition process analysis, the paper describes measuring method of zero time factor for transformer wire-wound resistor with specific exciting supply.
叙述了在自动控制、仪器仪表、信号变换以及传感器信号采集与处理等电路中实现大时间常数的一种新方法。
This paper introduces a new method for implementing the long time constant in the circuits of automation, apparatus, signal conversion, collecting and processing of sensor's signal, etc.
运用一阶单时间常数低通函数模拟运算放大器的开环增益，对RC桥式振荡电路进行线性分析，得出最大振荡频率为运算放大器增益带宽积的16.67%。
The maximum frequency of RC-bridge oscillator is 16.67% of gain bandwidth product of amplifier analyzed based on a first-order single time constant lowpass function model.
分析了直流电路中电感和时间常数对直流电弧熄灭的影响。
The affect of inductance and time constant to DC arc extinguishing in DC circuits was analyzed.
因此，电流镜(100)的每个晶体管限定数字模拟转换电路的步，相邻步之间的比率实质上是常数。
Thus, each transistor of the current mirror (100) defines a step of the digital to analog conversion circuit, and the ratio between adjacent steps is substantially constant.
由于单周控制单元中的积分器需采用模拟电路实现，模拟电路积分时间常数易受电路参数的变化而变化。
But one cycle controller is usually realized by analog circuit and the parameter is easy to vary with the environment, so the integration time constant will vary at the same time.
指出放电时间与电路时间常数以及电感和稳态电流的乘积相关。
It points out that arc dis charge time is related to circuit time constant and the product of inductance and static current.
论文详尽介绍了介电测量技术的原理及影响因素，并提出了利用集总电路模型求被测绝缘纸板的复介电常数的方法。
The thesis presents the measurement principle and its disturbance factors, as well as the method to obtain the complex permittivity of pressboard with a lumped circuit model.
论文详细介绍了介电测量技术的原理及影响因素，并用集总电路模型求解被测绝缘纸板的复介电常数。
The dissertation presents the principle of dielectrometry and its disturbance factors, and the methods to obtain the complex permittivity with a lumped circuit model.
介绍了利用微带电路来确定一组高性能、高频印刷电路板材料的介电常数和损耗角正切的方法，且给出了一组印刷电路板材料的特性测量值。
The paper introduces measurements about dielectric constant and tangential loss angle of a group of good function and high frequency printed electronic circuit plate with microstrip circuit.
该电路采取以恒流源为整流负载等有关措施，使整流二极管的正向导通压降为一常数。
In this circuit, some measures are adopted, such as making constant current source as a rectifying load. It makes the voltage drop of the rectifying diode maintain a constance.
为全面实现以上原则通过理论分析指出采用偏差输入将优于采用绝对值输入；采用时间常数可变的时限电路将优于采用平方电路。
It proves that it is superior to use the "deviation input" to the "absolute-value input" and better to use time circuit with variable time constant than to use square circuit.
本文简述了余度技术中的模型监控，介绍了籍助于模拟技术确定模型监控中各参数的方法，所得的参数——安全门限值和延迟电路的时间常数可作设计比较器的依据。
This paper gives an explicit description of the model monitoring in redundance technique It brings forth a method of determining parameters in model monitoring by using simulation technique.
本文简述了余度技术中的模型监控，介绍了籍助于模拟技术确定模型监控中各参数的方法，所得的参数——安全门限值和延迟电路的时间常数可作设计比较器的依据。
This paper gives an explicit description of the model monitoring in redundance technique It brings forth a method of determining parameters in model monitoring by using simulation technique.
应用推荐