本模型可用于电路分析程序，工艺容错分析及器件的优化设计。
This model is suitable for the circuit analysis program, process tolerant analysis and device design optimization.
本文提出了一个能在SPICE通用电路分析程序上运行的模拟相乘器的实用化动态宏模型。
A practical dynamic macromodel of analog multiplier suitable for the General Circuit Analysis Program SPICE is presented.
介绍基于PSPICE电路分析程序的自动优化设计系统及其在对数视频放大器设计中的应用和实验结果。
The automatic optimal design system is based on the circuit analysis software-PSPICE. In application, a video log amplifier is designed and the results are presented.
而且这也是非常重要的，因为程序员设计电路自检基于该电路中的分析——什么是好的电路和什么可能会导致失败。
This is important because the programmer designed the circuit self-test based on an analysis of a good circuit and what might fail within that circuit.
本文证明了两个定理，并由此提出了开关电容电路灵敏度分析的一种方法，此方法特别适合于用计算机程序来实现。
In this paper two theorems have been proved and a method of sensitivity analysis of switched capacitor circuits has been described.
对其电气性能、结构特点，故障诊断、接口电路及弧焊工作程序等作了比较全面的分析和讨论。
Its electric characteristic, structure feature, fault analysis, interface circuit and arc welding process program are analyzed and discussed.
分析了预处理循环控制流系统的特点：硬件电路的循环嵌套形式，预处理程序的设计思想。
The characteristics of pretreatment and cyclic control stream are analysed:the form of cyclic embedded hardware circuit, the idea for designing the pretreatment program.
介绍了利用89c52作为控制核心的混凝土砌块配料自动控制系统方案，并对其测量电路进行了分析，给出了较详细的程序流程。
This paper introduces the project of concrete burdening automation control systems base on 89c52, and analyzes the signal measuring circuit, also provides software program scheme.
电路最佳参数的选择是借助于反复使用SPICE分析程序来完成的。
Optimization of the circuit configuration was performed by means of iterative SPICE analysis.
通过对TC 35i模块的应用程序接口的分析，设计出它的外围电路，从而实现一个可以进行移动短消息收发的设备。
By analyzing the application program interface of TC35I wireless module, the peripheral circuit is designed. Through the device we can receive or send short messages.
在给出多种模型DC方程和源漏电容公式的同时，对三种电路模拟程序的应用范围进行了分析。
The DC equation and source drain capacitance formula of the models are given and the application range of three circuit simulation programs is analysed.
文章简要介绍了日立h- 600型电子显微镜抽真空系统，分析了抽真空程序及其程序控制电路。
The paper simply introduces the evacuation system for model H-600 electron microscope and analyzes the program of evacuation and the program control circuit.
在此基础上，给出了改进状态变量法的计算机实现方法，其计算程序是一套系统完整的状态变量法分析程序，具有很强的电路适用性。
On this basis, the realization of the analysis on a computer is given and the calculation program is a set of systematic and complete analytical program and has a powerful circuit applicability.
从原理上进行了分析，并设计了硬件电路和软件程序。
文章分析了它的主要特性，同时给出了73K222AL与单片机AT89C51的接口电路和应用程序设计。
The single-chip MODEM majors in MCU control system. This paper introduced the fundamentals of the chip, the interface circuit linking 73K222AL and AT89C51, and its programs.
设计了简单可靠的检测电路，并用程序流程图加以分析。
In the article the simply and reliable testing-circuit is desired and analysed by the program flow chart.
文章介绍一个用节点分析法计算正弦交流电路的程序。
A program based on the node analysis method which can be used to compute Sine AC-Circuit is described.
包括几种12864的使用手册，12864的使用说明，源代码及与at89s51相连接的电路图，点阵式LCD 12864接口与程序设计分析等等。
Including the use of some 12,864 manual, 12,864 instructions, source code and the circuit connected AT89S51, dot-matrix interface LCD12864 analysis and program design and so on.
最后将程序下载到电路中，对系统进行了调试和实验，并对结果进行了分析。
In the end, program is downloaded to hardware, system is debugged and experimented, and the result of experimentation is analyzed.
本文分析了原因，提出二级保护的方案，设计了工作程序流程图及逻辑电路。
This paper analysed the causes and proposed a two-grade protection measure. The working program flow chart and logic circuit are designed.
本文以三相桥式晶闸管整流电路为例，讨论波形分析法的原理、采样电路与微型计算机接口电路的设计及应用程序的设计。
As an example, the principle of waveform analysis, the design of sampling circuit, interface and applied programs for 3-phase bridge rectifier are discussed.
在电路和程序调试中，对遇到的一些实际问题进行了分析和解决，并找出了影响电路稳定性的诸多因素。
After debugging, some practical problems were analyzed and resolved; many factors that affected the stability of the circuit were found.
该分析程序在微机系统上对多种晶闸管电路、三相全控桥供电直流机系统、电流型逆变器驱动感应机系统进行数值分析，并与实验装置的波形比较，充分证明了该分析程序的正确性和实用性。
The simulation program in this paper has been applied to make digital simulation of several thyristor circuits, a DC-motor system driven by a three-phase full-wave rectifier circuit and an induction-…
该分析程序在微机系统上对多种晶闸管电路、三相全控桥供电直流机系统、电流型逆变器驱动感应机系统进行数值分析，并与实验装置的波形比较，充分证明了该分析程序的正确性和实用性。
The simulation program in this paper has been applied to make digital simulation of several thyristor circuits, a DC-motor system driven by a three-phase full-wave rectifier circuit and an induction-…
应用推荐