通过皮肤上面的或者插在病人耳朵后面的电磁感应器,就可以驱动一个微星控制器来操作人造心脏。
It is operated by a microcontroller and powered by electromagnetic induction through the skin or through a plug implanted behind the patient's ear.
这时控制器打开电磁阀并启动水泵加压,待水上满后两者将会同时关闭。
Then the controller opens the solenoid valve and starts the pump pressure, the water will be closed after the two will be closed.
经过多次试验,他终于决定以组成一个电磁铁和反馈系统的设置,与阿都伊诺为核心的微控制器。
After much experimenting, he finally settled on a setup comprising an electromagnet and feedback system, with an Arduino micro controller at the core.
控制器的输入信号为电磁阀升程,控制量是气门开启定时和开启持续时间。
Input signal of controller is solenoid valve lift. Control parameters are valve opening timing and valve open duration.
采用气体灭火控制器收集探测元件探测的信号来启动电磁阀,动作稳定可靠、反应灵敏。
Adopt gas fire extinguishing controller to collect signal to start the solenoid valve, the action is stable and reliable, reflect sensitively.
磁悬浮硬盘转子系统由定子、转子、电磁作动器、传感器、控制器和放大器等部件组成。
Hard disk rotors suspended by active magnetic bearings consists of stators, rotors, magnetic actuators, sensors, controllers and power amplifiers.
装置采取了可编程控制器作为新型控制系统,实现对模拟量的分析和对电机及电磁阀的控制。
The apparatus adopts programmable controller to the new style control system and can realize the analysis of analog variable and the controlling of motor and electromagnetism coil.
针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
To solve the chattering problem caused by general Sliding Mode control in active magnetic bearings control, a Boundary Layer Approach was used in the controller design.
本文主要进行电磁轴承控制理论、控制算法和基于DSP的控制器实现技术及应用研究。
In this paper, I main discuss electromagnetic bearing control theories, control algorithm and controller realization technique and application based on the DSP.
介绍了一种通用跳汰机电磁风阀控制器的设计思路,给出了相应的硬件组成和软件设计方法。
The paper introduces the design idea of microcomputerbased electromagnetic valve controller for general Jig, and it gives corresponding hardware component and software design method.
针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
This strategy combines the fuzzy logics with the method of sliding mode control, thus can reduce the chattering without decreasing the robustness of system.
该文采用保成本控制方法设计电磁轴承磨床电主轴系统控制器。
This paper USES a guaranteed cost control method to design a controller of the grinder spindle system supported by electromagnetic bearings (EMBs).
该主控制器通过电磁兼容测试、高低温及振动测试后,系统工作正常。
The main controller passed the electro-magnetic compatibility tests, high and low temperature tests and vibration tests and presented a normal working condition.
本文研究了轴向磁场无刷直流电机的电磁设计及其控制器的设计。
The electromagnetic field design and controller design of axial magnetic BLDC are studied in this paper.
为降低功率回路对微控制器的电磁干扰提供了新的途径。
It provides a new idea to reduce the EMI from power circuit to the microcontroller.
深入探讨了轮速传感器、防抱死制动电子控制器、电磁阀、回液泵的结构组成与工作原理。
The construction and working principles of speed sensor, ABS ECU, electromagnetic valve and return liquid pump are analysized in detail.
通过推导统一潮流控制器(UPFC)稳定控制器的状态方程,分析了UPFC稳定控制器对同步发电机电磁转矩的影响。
By analyzing the state equations of unified power flow controller (UPFC) stabilizer, the influence of UPFC stabilizer on electromagnetic torque of synchronous generator is presented.
介绍了一种跳汰机电磁风阀控制器的原理,给出了相应的硬件和软件的组成。
This paper introduces the principle of a kind of jig electromagnetic valve, gives out hardware and software.
该文介绍了西门子全数字直流调速装置(6ra70)和可编程逻辑控制器(SIMATICS7- 300)首次在码垛电磁铁系统中的应用。
This paper introduce the application of Siemens digital direct current timing device (6ra70) and program logical controller (SIMATIC S7-300) in piling bed electromagnet for the first time.
根据电磁场和磁流体力学理论,设计制造了以永磁体为工作介质,对金属液具有磁力驱动控制作用的双磁力驱动流体流动控制器。
Base on the theory of electromagnetic field and magneto hydrodynamic, an apparatus of double-driving by magnetic force media with permanent magnet has been designed and manufactured.
自动燃气控制系统包括电磁控制燃气阀、自动点火计时器及控制器。
Automatic gas control System including solenoid control gas valve and automatic ignition timer and controls.
控制器在线路设计上采取了一系列的抗干扰措施,可以在电磁干扰十分严重的环境中可靠工作。
The controller has taken a series of anti-jamming measures on the circuit design, can work reliably in grave electromagnetic interference environment.
定位器、P/P定位器、空气过滤减压阀、气动加速器、气控阀、限位开关、电磁阀、闭锁阀、速度控制器、阀位传送器等。
E/P Positioner, P/P Positioner, Air-set, Booster relay, Air-valve, Limit switch, Solenoid valve, Lock-valve, Speed controller, Position transmitter, etc.
分析了电磁轴承系统的刚度阻尼特性与系统结构参数及其控制器频响特性之间的关系。
The relations between stiffness and damping performances and structure parameters of an active magnetic bearing (AMB) system and frequency specificity of the control loop are analysed herein.
公司主要产品为电磁阀、热力膨胀阀、视液镜、干燥过滤器及压力、压差控制器。
Our main products include solenoid valve, thermostatic expansion valve, sight glasses, filter dryer, pressure controller, pressure difference controller , temperature controller.
电机及驱动控制器作为电动汽车的关键部件,其电磁兼容设计对于保证电动汽车的可靠运行非常重要。
The EMC design of motor and the drive control system is an important issue to assure the reliability of electrical vehicles.
本文还建立了此闭环控制系统的数学模型,通过数字仿真分析了其动态特性,探讨了控制器参数对转子运动的控制效果以及与电磁轴承动刚度之间的变化关系。
Also this closed loop controlled system is modelled and its dynamic behaviors are analyzed by digital simulation. The influence of controller parameters on motion of the rotor and th...
火灾报警控制器应符合GB4717-1993 标准的要求。检测项目有:静电放电;辐射电磁场;电快速瞬变脉冲群。
Control and indicating equipment (c. i. e) meets the requirements of GB4717-1993. The test items include Electrical transient bursts , Electrostatic discharge , and Radiated electromagnetic fields.
本文提出采用电磁阻尼器作为控制振动的执行器,选用数字PID控制器和变结构滑模控制器,使得控制系统具有更好的稳定性和方便性。
Electromagnetic damper as the actuator, using the digital PID control and sliding mode control of the vibration control system is presented in paper.
配备采用进口顺序控制器及脉冲电磁阀,品质稳定耐用,故障低。
Equipped with imported order control system and pulse electronic valve, the product has a stable and durable quality, and also has a low failure rate.
应用推荐