从模块上去除地金属屑被循环流动地电火花加工液冲走。
The metal particles removed from the die block are washed away with the dielectric fluid which is circulated.
从模块上去除的金属屑被循环流动的电火花加工液冲走。
The metal particles removed from the die block are washed away with the dielectric fluid, which is circulated.
研究了在大气和乳化液两种介质中，峰值电流对高速走丝电火花线切割加工的影响。
The influence of peak current on finishing high-speed wire electrical discharge machining (WEDM) in gas and emulsion dielectric is studied.
提出了一种基于复合工作液的、以电火花电解复合加工技术对太阳能硅片进行切割的工艺方法。
A solar wafer slicing method was studied, which was based on complex dielectric fluid and efficiency electric discharge machining (EDM) and electric chemical machining (ECM) technique.
利用水力旋流器对固体颗粒的分级、分离功能，设计了一种既能用于常规电火花加工又能用于混粉电火花镜面加工的通用型储液箱。
By using waterpower rotational flow device which can classify or separate solid grain from liquid, a utility dielectric tank used for common EDM and powder mixed dielectric EDM is designed.
为实现镜面电火花加工，向工作液中加入硅、铝或镍等粉末微粒。
It is one of the main processes in EDM to mix machining liquid with silicon, aluminum and nickel powder particles.
粉末沉降速度对混粉电火花加工工作液性能有重要影响，是实现混粉电火花镜面加工的关键。
Powder sedimentation rate has an important influence to powder mixed dielectric, and which is a man factor to realize powder mixed dielectric mirror EDM.
由于混粉电火花加工技术与普通电火花加工技术的最大区别是在工作液中添加的导电性粉末参与放电，粉末的存在对加工效果有重要的影响。
The remarkable difference between powder-mixed EDM and conventional EDM is that electric powder suspended in working fluid plays an important role in machining process.
利用国产铝粉作为混粉工作液的粉末添加剂，进行混粉电火花加工试验研究。
The homemade aluminium powder was used as the additive for powder-mixed dielectric EDM and the experiments were made in the EDM-tool.
提出了一种在普通电火花工作液中加入微细液态添加剂进行电火花光整加工的新方法。
A new EDM method is proposed in which microemulsion is mixed into the dielectric liquid.
混气电火花加工是在煤油工作液中混入空气的一种新型的电火花加工方法。
Air mixed Electrical Discharge Machining is a new method of EDM, this is method of making minor air bubbles contained in the kerosene.
本文的研究证明，高速平动液中喷气电火花铣削加工性能良好，是一种有效解决气中电火花加工短路率过高问题的方法。
It was proved that high Speed Assist Submersed Gas-jetting EDM Milling is an effective solution to solve high short circuit ratio problem of EDM in gas, and reveals good machining performance.
液中电火花铣削加工时相对稳定，但电极相对损耗严重，妨碍了电火花加工性能的提高。
The Traditional EDM can achieve stable discharging but the electrode wears dramatically, which decreases the EDM milling performance.
为有效地实现微细金刚石砂轮的修锐，建立单脉冲电火花放电去除加工的试验系统，研究金属结合剂的气中和液中电火花放电去除机理。
In order to realize dressing of fine diamond grinding wheel effectively, removal behavior of metal bond for dry and wet coolants is investigated.
结果表明，采用水基工作液电火花加工，电火花加工后高温回火处理及喷丸强化等措施，都可提高试样的冲击疲劳寿命。
The results show that the impact fatigue life-time of the specimen will increase by means of high-temperature temper and shot-peening after EDM with the water-base working fluid.
结果表明，液中喷气电火花加工放电瞬间加工区域是处于气体包围中的。
The results indicated that the working area is completely surrounded by the high-pressure gas and the discharge happens in the gas.
通过在普通和混粉工作液中的大面积电火花加工实验对比，证明以上结论的正确性。
The comparing experiments in common dielectric and powder-mixed dielectric prove the conclusions are correct.
研究了高速走丝电火花线切割加工中切割效率、表面粗糙度、表面微观形貌的变化，指出采用切割效率作为工作液失效的表征更为直观和准确。
The changes of cutting speed, surface roughness and surface topography were researched. Adopting cutting speed as characterization of cooling liquid failure is more intuitive and accurate.
研究了高速走丝电火花线切割加工中切割效率、表面粗糙度、表面微观形貌的变化，指出采用切割效率作为工作液失效的表征更为直观和准确。
The changes of cutting speed, surface roughness and surface topography were researched. Adopting cutting speed as characterization of cooling liquid failure is more intuitive and accurate.
应用推荐