该电源由一个电源控制模块和多个电源变流模块组成。
The power supply consists of a power control module and several power converter modules.
介绍了一种基于TMS320C 6713和FPGA的数字电源控制模块，给出了模块的硬件组成和软件设计。
Digital power controller based on microprocessor TMS320C6713 and FPGA is introduced. At the same time, the constitution of the hardware and software are introduced too.
这个指导纲要涵盖了LED光源的零部件，诸如LED模块，LED阵列，电源和控制电路。
The outline covers the component parts of a light emitting diode (LED) light source such as LED modules, LED Arrays, power sources and control circuitry.
控制系统主要由电源电路、数字控制电路和机械控制电路三大模块构成。
Hardware system is made up of three modules: power supply circuit, digital control circuit and machine control circuit.
主要介绍CPCI数字存储示波器模块的模拟通道设计、A/D采样设计、数字控制电路设计、电源设计以及CPCI接口设计。
The hardware design of the module mainly presents analogue channel circuit design, A/D acquisition circuit design, digital control circuit design, power and CPCI interface design.
本文致力于模块化逆变电源并联控制系统的研究。
This dissertation focuses on the research of parallel operation control system about modular inverter.
定时电路一般由电源模块、面板电路和定时板组成，是功率源中的数字控制部分。
Timing circuit is usually made up of power supply unit, panel circuit and timing board, it is the digital control part of power source.
它以SA 4828作为SPWM信号发生器，经过驱动电路控制IPM模块，产生三相变频电源。
The SA4828 used as SPWM signal generator controls the IPM via driver circuits to produce variable frequency power supply.
包括单片机控制、电源、传感器、油量报警、油量显示、车速信息、里程信息、LED显示等模块设计和软件的设计。
It consists of MCU control, power, sensor, oil amount warning, oil amount show, LED display and the software design.
本课题是对无工频变压器开关电源控制器芯片模块电路的设计与研究。
My project is focused on the design and research of PWM switching power supply control circuitry that requires high efficiency and reliability.
AT 89s52作为显示模块的控制核心，实现功率放大器输出功率、直流电源的供给功率和整机效率功能的显示。
AT89S52 as a display module to control the core of achieving power amplifier output power, DC power supply of power and machine efficiency, for display.
系统在硬件结构上分为控制、驱动、电源、显示、电压转换五大模块电路，各电路板之间采用磁耦进行隔离。
The system hardware architecture is divided into control, drive, power supply, display five blocks circuits, and magnetic coupling is used to isolate circuit boards.
电源模块为系统控制电路、变频驱动电路、变送电路、DSP芯片提供不同要求的电源。
The power supply module provides the control circuit, the drive of frequency conversion circuit, transaction circuit and DSP with different power supply.
介绍了机器人控制系统的总体设计方案，包括电磁铁驱动模块、CPLD扩展模块、无线通信模块、电源模块等。
The paper gives the whole control system design of the in-pipe robot, which includes electro-magnet drive module, CPLD patulous module, wireless communications module, power module.
提出了一种新型分布式控制方法来实现单相数字模块化ups(不停电电源)的并联运行。
A novel distributed control scheme is proposed for the parallel operation of single phase digital controlled UPS (uninterrupted power supply).
其硬件部分主要由六个模块组成：信号调理模块、时间校对模块、存储器模块、网络控制模块、WDT模块和电源管理模块。
The hardware mainly comprises six modules: signal procession module, time adjusting module, memorizer module, network control module, WDT module and power management module.
该结构是以分层递阶控制为主体系统结构，引入了基于模块化分布式电源管理系统，并在传感/底层决策层采用了基于包容式体系结构。
It is a hierarchical control structure for the main system, which a modular-based Distributed Power Management System is introduced in.
设计分电源，AD和DA转换，电流源输出，显示和控制模块。
The design includes power source, AD and DA conversion, output module of current-source, demonstration and control module.
介绍了利用高频开关管IGBT构成模块化充电电源的主电路、控制电路及保护电路的结构、原理。
The structure and theory of main circuit, control circuit and protection circuit of modularized charge power supply composed by IGBT high frequency switch tubes are introduced in this paper.
设计中还增加了功能电路包括比较器及一些逻辑控制模块，保证基准源电源供电切换顺利；
In addition, the structure increase a functional circuit including the comparator and logic control modules to ensure the reference source working perfectly.
系统硬件电路包括音频数字信号源实现声音信号产生、数字声强级控制、多机数据通信、液晶显示和电源等模块单元。
System hardware circuit audio digital signal source achieve this functions: sound signals, sound intensity level control, data communications, liquid crystal display, alarm and power.
为提高系统的可靠性，还设计了对电源控制保护器功能模块的自检测（BIT）电路和采取了有效的硬件与软件抗干扰措施。
To improve the system reliability, the build-in-test( BIT) circuits are also designed, and the effective hardware and software anti-disturbance methods are adopted.
本论文完成了屏蔽门控制系统的硬件电路设计，包括电源模块、控制模块、驱动模块的设计。
In this paper, the design of the PSD control system's hardware, which includes the power module, the control module and the drive module has been made.
控制系统主要由电源电路、数字控制电路和机械控制电路三大模块构成。
Control system mainly consists of power circuit, digital control circuit and mechanical control circuit constituted the three major modules.
基于直流屏的电源监控系统的各模块功能划分与采样通道多等特点，设计了以MSP430单片机为控制核心，CPLD扩展端口的控制系统。
Based on function partition of modules and much sampling channels of power monitoring system for DC screen, a control system which takes MSP430 as control core and CPLD as extending ports is designed.
首先，对应用系统进行了功能模块划分，将其分为了测量模块、微控制器模块、存储模块、显示模块、通讯模块和电源模块五部分。
First, the application system is divided into five function modules: the measurement module, microcontroller module, memory module, display module, communication module and power module.
设计开发的电除尘器电源控制器采用ARM9系列STR912微控制器作为主控芯片，供电电源及信号输入输出模块采用光耦隔离设计方案。
Power controller adopts STR912 of ARM9 series as microcontroller, and USES the technique of optical coupling isolation within the input, output and power supply module.
本文还研究设计了清扫机器人各个部件模块的供电情况，分类供电，特别是动力电源和控制电源，尽量避免相互干扰。
The article also have made a study of the power supply for each part, classify the power supply types, especially drive power and control power, in order to avoid disturbance each other.
本文还研究设计了清扫机器人各个部件模块的供电情况，分类供电，特别是动力电源和控制电源，尽量避免相互干扰。
The article also have made a study of the power supply for each part, classify the power supply types, especially drive power and control power, in order to avoid disturbance each other.
应用推荐