电枢电压和外负载转矩是系统的输入。
The armature voltage and external load torque are inputs to the system.
由控制电路实现焊接程序的控制，带电枢电压负反馈的调速电路控制和调节送丝速度。
The control to welding procedure is realized by a control circuit, and wire feed rate is regulated and controlled by speed governing circuit with the armature voltage negative feedback.
在中小型直流调速系统中，一般都取消了测速发电机，而以电枢电压作为电机转速信号。
In general, tachometer generators are eliminated in the small and medium power DC rotating speed governing systems, and armature voltage is used as motor speed signal.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjusters were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjustors were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
本文针对全数字直流调速器回路、应用自适应原理，通过数学推导，得出了速度环、电枢电压环、电枢电流环的数学模型。
According to the loops of the total digital DC timing and applied self-adaptive principles, deduce the mathematic model of the speed, armature voltage and armature electrical current loops.
作者通过对实际系统的分析和动态模拟试验的验证，对其由于换相及电枢反应引起的输出电压降低作了较为详尽的、定量的分析。
The author evaluated the output voltage drop owing to the commutative process and armature reaction in detail by means of the analysis of the existent system and the dynamic simulation experiments.
这款可靠的直流发电机可根据电枢轴的旋转速度直接提供电压输出值，该设计应用于速度控制应用领域。
These reliable direct current generators provide a voltage output directly proportional to the rotational speed of the armature shaft and are specifically designed for speed control applications.
产生感应电压的绕组称为电枢绕组。
The winding in which voltage is induced is called the armature winding.
实验结果表明：在电枢初始位置不变的情况下，弹丸初速度与电容器组的充电电压几乎成线性关系；
The experimental results showed that muzzle velocity of the projectile was almost linear with the charging voltage of the capacitor bank when the initial position of the armature was fixed.
发电机电压与系统电压之差必须足够小，避免合闸时发电机电枢绕组电流过大，对发电机联轴系统产生冲击。
The voltage between the system and generator must be small enough to ensure minor current in the armature winding of generator, avoiding the impact to the coupling shaft.
该锁配备12/24伏电压传感输入，门静态和对准传感器，横向和纵向对准调整，以及浮动电枢。
The lock features a 12/24 VDC voltage-sensing input, door static and alignment sensor, lateral and vertical alignment adjustment, and a floating armature.
输出电压的特点是根据插槽潜力的星图，分析和电枢绕组的设计约束。
Characteristic of output voltage is analyzed according to the star graph of slot potential, and the design constraints of armature windings are provided.
所比较的变量有电枢相电压和相电流、励磁电流、负载电流以及阻尼条电流。
The variables compared include the phase voltage and the phase current of the armature winding, the field current, the load current and the damper bar currents.
伺服电机有轻量级、低惯性电枢，励磁电压变化做出快速响应。
Servo motors have lightweight, low-inertia armatures that respond quickly to excitation-voltage changes.
伺服电机有轻量级、低惯性电枢，励磁电压变化做出快速响应。
Servo motors have lightweight, low-inertia armatures that respond quickly to excitation-voltage changes.
应用推荐