对比分析了电流密度、添加剂对工具电极损耗的影响。
Analyzing the effects of current density and additives on tool-electrode wear.
分析了该方法的工艺特点；研究了实现该技术的条件及电极损耗补偿策略。
This paper analyses its machining characteristics and studies the conditions that bring this technology into use, then gives. the policy of electrode compensation in actual machining.
介绍了对电火花成形加工中产生的电极损耗进行自动测量及自动补偿的方法。
The method of automatically measuring and compensating the electrode loss that occurring in the EDM machining was introduced.
介绍了对电火花成型加工中产生的电极损耗进行自动测量及自动补偿的方法。
Electrode loss, which occurs during the electrospark moulding process can be automatically measured and compensated.
由于电极损耗的因素，使得工件的形状和尺寸的一致性不好，且对生产率也有影响。
The mode of radial feeding is used ever, but it can not get the good shape of parts and conformance of size and influence the productivity even.
镀层具有良好的可焊性和导电性，其电极损耗低于银电极损耗，可作为代银接触镀层。
Ni B plating possesses good weldability and conductivity, and the electrode loss is lower than that of silver electrode. It may be used instead of silver plating.
根据电火花铣削等损耗理论，对用电火花铣削钛合金的加工中电极损耗补偿作了分析阐述。
Based on equivalent loss of EDMMILL, analyze the compensation of electric pole in EDMMILL to TA4.
进行微细电火花三维扫描加工时，由于电极损耗相对严重，导致形位公差难以保证和加工效率较低。
In 3d scanning process of micro electro discharge machining (micro EDM), the machining efficiency and geometrical tolerance are difficult to be guaranteed due to the serious electrode wear.
并对用不同电规准加工时的电极损耗机理和生产率（加工速度）作出了分析和探讨，得出了相应的结论。
Mechanism of electrode loss and machining rate are analyzed when different electrical parameters are used and then corresponding conclusion is obtained.
此外，气体介质中电火花加工工具电极损耗低的特点有利于实现气中电火花削加工工具电极损耗的补偿。
In addition, the feature of low electrode wear ratio of the electrical discharge machining in gas (dry EDM) is helpful to implement the tool electrode wear compensation in dry ED-Milling.
对电火花铣削加工中电极损耗状态的获得及其补偿技术进行了分析研究，提出了电极损耗的各种补偿策略。
An analysis and research are made on the techniques of monitoring the tool wear state and its compensation in EDM milling. Compensating strategies for the tool wear are proposed.
线电极放电铣削加工是一种新型电火花铣削技术，它的最大优点是可通过线电极的缓慢移动来补偿加工中的电极损耗。
Wire Electrical Discharge Machining Milling (wire EDM-Milling) is a novel kind of EDM-Milling method that has the distinct advantage of electrode compensation via the wire electrode slow traveling.
增强工具电极材料的耐电蚀能力，降低电极损耗是微细电火花加工技术可靠、稳定且高效制造高深宽比微结构和器件的研究关键之一。
Enhancing electrical erosion resistance of tool electrode and reducing electrode wear is one of research keys to fabricate HARMs with micro EDM technology reliably, stably and efficiently.
针对三维金属微细结构的微细电火花加工，应用等损耗理论，采用分层加工的方法，建立了单道加工时底面形状随电极损耗而变化的轮廓模型。
Micro 3D structure machining with simple shaped electrode can't generally apply the method of common mechanical milling for the reason of electrode wear, Machining conditions and etc.
通过这个过程，当工具电极(阳级？)只有极小的损耗时材料便获得了了迁移速度，并且并不危害副表面。
During the process, high material removal rates are obtained while the tool electrode wear is extremely small and the sub-surface is not damaged.
根据伏安曲线分析了质子交换膜燃料电池(P emfc)的电极热源项和能量损耗比例。
Heat sources of the electrode and their proportion of the energy wastage in PEMFC were analyzed by the voltammetry curves.
气中电火花加工时电极相对损耗很小，但由于短路率过高导致加工不稳定、材料去除率不高，还会产生烧焦气味。
EDM in gas can make less electrode wear, but its high short circuit ratio will lead to unstable process and thus low material removal rate.
液中电火花铣削加工时相对稳定，但电极相对损耗严重，妨碍了电火花加工性能的提高。
The Traditional EDM can achieve stable discharging but the electrode wears dramatically, which decreases the EDM milling performance.
因此，研究荧光灯启动机理并寻找能降低其电极上电子粉损耗的其它启动方式，是提高荧光灯寿命的一项重要研究工作。
Therefore, researching the mechanism of the fluorescent lamp so to find another start-up mode to reduce the waste of the electric powder on the electrode may improve the fluorescent lamp's life-span.
在荧光灯启动时，电极上的发射物质(电子粉)溅散、损耗最为严重。
When the fluorescent lamp starts-up, the sputtering and waste of the missile on the electrode is most serious.
通过计算发现，随着中间电极角度和地电极角度增加，有效折射率、特征阻抗同时减小，导体损耗系数也随之减小。
The calculation results have shown that when the angles of the center electrode and the grounds decrease, the effective index, the characteristic impedance, and the conductor loss all decrease.
SL回路可将电极之损耗降低50%；PL回路为超硬合金专用，加工速度快。
The SL circuit reduces electrode wear to 50%. Specially designed PL circuit is excellent for hard alloy workpiece with fast machining speed.
电火花加工中，放电介质对工件的材料去除率、表面质量以及电极相对损耗率有重要影响。
In the process of EDM, dielectric medium has remarkable influence on material removal rate, surface quality of the workpiece and relative electrode wear ratio.
在电火花铣削加工中，由于工具电极作旋转运动，其损耗呈轴对称分布，使工具电极的补偿成为可能。
In electric discharge milling machining (EDMM) process, the rotation of the tool electrode makes tool wear be axial symmetrical distribution, so it is possible to be compensated.
文章还提出，采用后三角形电流脉冲能较好的适应石墨电极材料，加工后电极表面平整，相对损耗小。
Having been equipped with it, the triangular current pulse is more suitable to the graphite electrode, the surface uniformity of electrode is improved and the relative wear is reduced.
聚酯膜有感结构，环氧树脂包封，体积小，重量轻，引线直接焊于电极，损耗小。
Polyester film feeling construction, inductive, epoxy resin coating. Small size and light weight. Small dissipation factor, the leads directly welded to electrodes.
聚酯膜有感结构，环氧树脂包封，体积小，重量轻，引线直接焊于电极，损耗小。
Polyester film feeling construction, inductive, epoxy resin coating. Small size and light weight. Small dissipation factor, the leads directly welded to electrodes.
应用推荐