进口松下电机伺服控制系统，提供精确位移及速度控制。
Servo motor control system Imported from Japan Panasonic, provide accurate displacement and speed control.
实验结果与理论分析基本一致，为高性能直线电机伺服控制器的改进设计提供了客观数据。
The results of experiment justify the validity of the analysis model, which is useful for the further design of high performance servo controller of PMLSM.
为了设计高精度的直流无刷电机伺服控制系统，性能优良的位置跟踪控制器是其重要保障。
The position tracking controller with good performance is the guarantee of high precision brushless DC motor servo system.
介绍了一种基于DSP的无刷直流电机伺服控制系统，简述了实现该控制系统的软件和硬件设计方案及控制策略。
This paper presents bushless DC motor servocontrol system based on DSP, then makes a brief about control strategy and design scheme of software and hardware that realizes this control system.
您可以通过修正两个输入参数改变伺服电机的位置来建立新的循环控制。本功能将对影响燃烧过程的所有因素进行补偿。
You can shift the position of the servo motors via two correction inputs, ie. to build up a control loop. This compensates all interference which influences the firing process.
一种采用脉冲控制方式，此种驱动器与电机闭环，但不反馈到数控系统，这种驱动器在某种程度上可称为开环控制的伺服控制。
A kind of the pulse control mode, the drive and motor closed loop, but not to the numerical control system, the feedback device, in a sense, can open loop control called the servo control.
目前常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Now commonly used servo motor is ac servo motor, the axial end in motor with photoelectric encoder, by examining the rotor Angle to frequency conversion control.
伺服电机可精确控制箱中的液位。
A servo motor accurately controls the fluid level in the tank.
吸风口由伺服电机精准控制，跟随边自动调整。
Auto suction outlet system. Suction outlet controlled by servo motor precision, following the knife edge automatic adjustment.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Adopting ac servo motor as the driving device, can the dc servo motor and a high precision, high performance as the half closed loop or closed loop control system.
设计一种伺服电机控制系统。
介绍自行研制的基于80C196KC单片机的交流伺服电机控制卡的硬件设计及其软件实现。
The paper introduces the hardware and software design of an AC servo motor control card based on 80C196KC.
准确的定位和控制由伺服电机编码器。
The positioning and accuracy are controlled by encoders from servo motors.
采用全数字技术实现对交流永磁同步电机的伺服控制，并将此项技术应用于工业缝纫机领域。
The full digital technique was adopted to realize the servo control of the ac permanent-magnet synchronous (motor.) the technology was applied in the industrial sewing machine.
选用动态混合时，采用新型混合器，伺服电机控制，转速可调，而且噪音很小。
The dynamic hybrid, using a new type of mixer, servo motor control, speed adjustable, and the noise is very small.
再用电机伺服驱动系统控制天线转动，调整其重新指向卫星接收信号。
The motor servo drive system was used to control antenna turning, adjust the antenna to point at satellite again and receive signal.
电机现代控制技术是伺服驱动系统的核心，也是现代制造装备最具代表性的先进标志之一。
The modern control technology for motor is not only the core of servo drive systems, but is one of the most typical symbols of modern manufacturing equipments.
介绍了基于TMS320F2812交流伺服电机控制系统的整体方案设计。
The whole project design of the AC servo motor control system based on TMS320F2812 is introduced.
仿真实验及在伺服电机转速控制中的应用表明，该算法具有较快的学习速度及良好的收敛性能，并有效地克服了传统PID算法的缺陷。
The simulation and motor control show that the new algorithm has fast learning rate, good convergence properties and can overcome the defects of traditional PID algorithm.
机械臂的系统控制硬件主要包括伺服电机系统﹑控制单元﹑运动控制单元﹑上层管理单元。
The control system of the manipulator consists of servo motor control unit, motion control unit and top management unit.
变频器控制主传动，伺服电机、气动控制自动落纱，性能安全可靠。
The inverter controls main drive, the serve motor, the pneumatic components control the Auto-doffer. The machine ensures safety and reliability.
采用台达交流伺服电机及控制器实现精确定长剪切，全闭环控制。
DELTA AC servo motors and controllers to determine the precise length cut, closed loop control.
该运动控制卡能同时采集四轴的编码器脉冲信号，输出四路模拟电压控制伺服电机，同时能控制I/O信号的输入和输出。
The card can collect four axes' encoder pulse signals simultaneously, and control servo motor by four output analog voltage. Furthermore, it can control input and output I/O signals.
然后，本文探讨了机器人运动学正逆解求解方法和伺服电机控制算法，详细地讨论了其中的PID算法。
Then the paper discusses method of robot's kinematics and inverse kinematics and robot's control arithmetic mostly about PID control.
而伺服刀架的核心技术就是伺服电机的位置控制技术。
And the key technology of the servo turret is the position control technology.
本文提出了基于DSP的永磁同步直线电机全数字伺服控制与驱动系统。
In this paper, the DSP-based all-digital servo and driving system for the permanent magnet synchronous linear motor is proposed.
介绍了重复控制技术在直流直线伺服电机控制系统中的应用。
The application of repetitive control technology in control system of linear DC servomotor is presented.
运用运动控制芯片MCX314实现了伺服电机控制模块的设计，提高了数控系统的实时响应性和可靠性。
MCX314 was selected to realize the design of servomotor module in this project, improved the CNC system's characteristic of real time and reliability.
运用运动控制芯片MCX314实现了伺服电机控制模块的设计，提高了数控系统的实时响应性和可靠性。
MCX314 was selected to realize the design of servomotor module in this project, improved the CNC system's characteristic of real time and reliability.
应用推荐