探讨了计算理论燃烧温度的方法及推导过程。
The paper discusses the computing method and computing process of theoretical burning temperature.
理论燃烧温度是反映炉缸热状态的重要参数之一。
Theoretical flame temperature is considered as one of the important parameters which reflect the thermal state of a hearth.
炉缸温度主要由风口理论燃烧温度与铁水温度反映出来。
The hearth temperature is reflected by the theoretical combustion temperature at the tuyere and the temperature of the liquid iron.
论述了高炉煤气富化分离对提高热风炉理论燃烧温度的重要意义。
The significance in increasing theoretical hot stove burning temperature by blast furnace gas enriching and separating was expounded in this paper.
煤气燃烧时机械水气化耗热要降低理论燃烧温度，其影响不可忽略。
Gasifying the liquid water cannot be neglected because it is heat consuming, thus decreasing the theoretical combustion temperature.
通过对物料、热量平衡的计算得出全氧高炉喷吹高氢燃气工艺风口理论燃烧温度。
Through calculating the balance of material and heat, the theoretical temperature of combustion of blowing tuyere in the co- injection of natural gas with pure oxygen BF process was stud-ied.
在介绍新型燃磷塔结构的基础上，提出了计算其理论燃烧温度和烟气排放温度的工程方法。
Based on the introduction to a new-type phosphoric furnace structure, an engineering method for calculating the theoretical combustion temperature and smog exhaust temperature was proposed.
基于回旋区边界上力的平衡，并考虑理论燃烧温度和有效直径等的影响，建立了同类型竖炉风口回旋区的简化模型。
A simplified raceway model of the shaft furnace was build based on the force balance at the raceway border and by considering the influences of flame temperature and effective raceway diameter etc.
这一研究成果从理论和实践上为动力工程中燃烧过程温度的动态测试打下了良好基础。
The development presented here, both theoretical and experimental have laid the foundation for the dynamic measurement of the combustion process temperatures in the thermal engineering.
烘干系统中燃烧器的燃烧温度是至关重要的参数，本论文针对燃烧室温度控制作理论上的研究。
In the drying system the combustion temperature of burner is the very important parameter, contrapose the burner, makes theoretically research of temperature controlling.
针对六角切圆燃烧锅炉水平烟道入口烟气温度偏差问题，利用模化理论建立试验台，进行冷态模化试验。
Aimed at the deviation of gas temperature in the input of level gas flue of six angles tangential firing boiler, the cold modeling test is put on building the test stand by using the modeling theory.
这一研究成果从理论和实践上为动力工程中燃烧过程温度的动态测试打下了良好基础。
The development presented here, both theoretical and experimental have laid the foundation for the dynamic measurement of the combustion process t...
结果表明，相对强度法能准确地测出单元推进剂HNIW在整个燃烧过程的温度分布曲线，测得的最高燃烧火焰温度低于相应压力下的理论计算温度；
The (investigation) results show that the curves of combustion flame temperature distribution in all combustion course are accurately measured by relative intensity method for monopropellant HNIW.
研究了燃烧波波速、火焰传播速率、最高燃烧温度等燃烧特性参数，将计算结果与实验结果以及前人的理论结果进行对比。
Some characteristic parameters, such as the combustion wave velocity, the flame speed and the peak flame temperature, are predicted. Analytical results have been compared with the related e...
研究了燃烧波波速、火焰传播速率、最高燃烧温度等燃烧特性参数，将计算结果与实验结果以及前人的理论结果进行对比。
Some characteristic parameters, such as the combustion wave velocity, the flame speed and the peak flame temperature, are predicted. Analytical results have been compared with the related e...
应用推荐