对城市垃圾与煤混烧飞灰进行旋风熔融试验，分析了不同熔融温度条件下熔渣的微观形貌及重金属行为。
The melting characteristics and behavior of heavy metals of fly ashes were investigated under different melting temperatures.
托雷斯 -桑切斯，与斯特拉斯克莱德大学的同事一起，正在试验当聚合物开始冒泡的时候，用低频率的超声波照射来“激发”熔融聚合物。
Torres-Sanchez, along with colleagues at Strathclyde University, is experimenting with low-frequency ultrasonic irradiation to ‘excite’ molten polymers as they begin to foam.
通过研究样品的熔融，及干扰元素的试验，提出熟矾土中二氧化钛的测定条件。此方法快速、准确。
Proposes the determination conditions of titanium dioxide in bauxite by studying the melt of samples ane testing the interference elements. The method is rapid and accurate.
经过反复的工艺试验及一年多批量生产验证，成功地将熔融石英应用于精铸用低温蜡—硅溶胶型壳生产中。
By repeating technological tests and batch production tests for over a year, the fused silica was successfully used in the production of silica sol shell for low temperature wax precision casting.
采用数学模型推算了熔融碳酸盐燃料电池隔膜寿命，并进行了单电池运行稳定性试验。
The life of matrix for molten carbonate fuel cell (MCFC) was estimated by adopting mathematical model and the operating stability of single cells was tested.
对铝合金熔融发泡工艺进行了研究，用火山灰作发泡剂、用钙为增粘剂。通过试验，认为用此法制造泡沫金属是可行的。
This paper researches on the foaming procedure of aluminum alloy in molten state and believes that the procedure is feasible for making foam metals.
通过对比试验发现：测定炭素材料中二氧化硅的含量，熔融法的分析结果比氢氟酸法更稳定、准确；
The comparative tests show that the content of silicon dioxide in carbon materials determined by the melting method (MM) is more stable and accurate than the hydrofluoric acid method (MHA);
模具设计人员可按压铸时熔融金属的温度及对模具抗熔损性能的要求，参照试验结果进行选材和确定模具的硬度。
With reference to the test result, die designers may select material and determine hardness of dies according to the temperature of melt metal and the demand for the resistance to erosion.
经生产应用试验表明，该保护渣熔融性能稳定，无分熔现象，粘度适中，吸收氧化铝夹杂物能力强。
The practical application shows that the mould powder is characterized by stable melting performance, non-fractional melting, moderate viscosity and high capacity of absorbing Al2O3 inclusion.
本文中，以粉煤灰为原料，采用碱熔融-水热合成法制备a型沸石，并将其用于制革废水批处理振荡试验。
By using coal fly ash as main material, the alkali fusion-hydrothermal synthesis method was adopted to prepare zeolite-A and apply it to tannery wastewater treatment in this paper.
应用对滚圆盘磨损试验机研究了合金铸铁经激光熔融处理后的耐磨性，试验结果指出，激光处理试样的磨损失重大为减少。
The roll disk wearing testing machine is used to study the wearability of alloy cast iron after laser melting. The test result shows that the wear weightlessness is reduced greatly.
作者就含碳铬矿球团在竖炉内熔融还原冶炼铬铁合金的新工艺进行了试验。
Trials of a new smelting reduction process for ferrochromium manufacture in shaft furnace with carbon bearing chrome-ore pellet was carried out by the authors.
作者就含碳铬矿球团在竖炉内熔融还原冶炼铬铁合金的新工艺进行了试验。
Trials of a new smelting reduction process for ferrochromium manufacture in shaft furnace with carbon bearing chrome-ore pellet was carried out by the authors.
应用推荐