熔渣覆盖降低了钢液吸氮速度。
The covered slag reduces steel fluid attracting nitrogen speed.
一旦冷却，这种熔渣就可以用来制砖或者铺路。
Once it has cooled, this slag can be used to make bricks or to pave roads.
快速颠倒钢水包从包里倒出熔渣。
Quick reverse tilt the ladle to remove slag from the pouring spout.
焊割作业有大量的火星飞溅和熔渣。
Soldering could cause numerous of spattered sparks and fused dregs.
煤灰与熔渣的熔融特性存在一定差异。
冶炼钢铁所产生的粒状熔渣(熔渣砂)。
Granulated slag (slag sand) from the manufacture of iron or steel.
有的化成气体跑掉了，有的结成了熔渣。
Some come off in the form of gases , others collected as slag.
在钢铁冶金过程中，熔渣的起泡现象是非常普遍的。
During the steel metallurgy, the phenomena of slag bubbling up is very prevalent.
金属和其他不能变成气体的无机材料，则会作为熔渣落到箱底。
Metals and other inorganic materials that do not turn into gas fall to the bottom of the chamber as molten slag.
提出平均发泡寿命作为熔渣发泡效果的实验评价指标。
Average foams life, has been presented as criterion to evaluate the foaming behavior in mol-ten slag.
焊后应用不锈钢(不得采用碳钢)扁铲彻底清理熔渣和飞溅。
Application of stainless steel after welding (not by steel) flat shovel thoroughly clean slag and spatter.
双层药皮焊条熔渣渣的组织继承了外层药皮渣组织的特征；
The microstructure of slag is inherited the one of outside layer coating slag.
当气体冷却，任何有毒的物质会被封在玻璃状的熔渣中，被安全的填埋。
When the gas is cooled, any hazardous elements in the waste end up sealed in a glassy slag that is safe to put into landfill.
熔渣中过渡族金属的热力学是冶金基础研究的一个重要方面。
Thermodynamic behaviors of transition metals in molten slags are an important aspect in the fundamental research of metallurgy.
罐内结壳，熔渣或脱氧浮渣扫除问题的几项解决方案正在实验中。
Several approaches to the problem of ladle skull slag or deoxidation-scum removed was being tried.
冶炼钢铁所产生的熔渣、浮渣(粒状熔渣除外)、氧化皮及其他废料。
Slag, dross (other than granulated slag), scalings and other waste from the manufacture of iron or steel.
那些没能转化为气体的金属物和无机物质则被视为熔渣，留在熔炉炉底中。
Metals and other inorganic materials that do not turn into gas fall to the bottom of the chamber as molten slag.
结果表明，熔渣降低真空脱氮速率，底吹氩能减少熔渣对真空脱氮的阻力。
It is found that slags decrease the rate of vacuum denitrogenation and vacuum argon blowing decreases the denitrogenation resistance of slags.
脱硫不涉及氧化，而是取决于熔渣是否有足够的碱度以及其温度是否足够高。
The removal of sulphuric doesn't involve oxidation, but depends on whether the slag is sufficiently basic and the temperature is high enough.
本技术可适用于各种金属冶炼的熔渣处理，金属和非金属熔融制粒等生产过程。
The techniques can be applying into the production process of slag disposing of all kinds of metal smelting, metal and nonmetal melting and making grains.
研究了超低碳钢保护渣的显微组织结构特征，并根据相图分析了熔渣的结晶性能。
The characteristics of the microstructure on super low carbon steel powder has been studied, and the crystallization performance of slag analysed by phase diagram.
通过气化机理分析认为，双高煤采用非熔渣气化、固态排灰的操作方式是可行的。
After analyzing gasification mechanism, it is believed that the operation of dry ash process can be used.
现有的气流床气化技术均为高温熔渣气化技术，使国内资源丰富的双高煤无法利用。
All the existing entrained-flow gasification technologies belong to the technology of high slagging temperature process so that domestic resourceful double-high coal cant be used.
金属陶瓷具有良好的耐热态金属及熔渣侵蚀性能，可实现对高温熔体温度的连续测量。
The cermet had merits of high resistance to corrosion of hot metal and slag, it can be used for continuous temperature measurement.
在宝钢炼钢厂300t RH-KTB上进行了超低碳超低硫钢的预熔渣深脱硫试验。
The industrial desulfurization test on 300 t RH-KTB unit at Baosteel using premelted slag was carried out.
通常表现是切割射流的吹力减弱，切口下部残留的熔渣增多，上部边缘过熔而出现圆角等。
Usually the performance is a cut of the jet blew force is abate, the lower incision of the remainder of the slag increased, the upper edge of the melt and appear a round, etc.
需焊接或热切割的表面应排除所有可能会损坏焊材或母材的杂物，如脂、油、灰尘、水垢、熔渣和油漆等。
Surfaces to be welded or thermally cut shall be cleaned of all foreign material such as grease, oil, dirt, scale, slag and paint that would be detrimental to either the weld or base material.
讨论熔渣发泡现象的实质，建立泡沫渣发泡幅度的理论模型，并结合实验数据讨论了模型参数。
The essential of the foaming phenomenon in molten slag was discussed, and mathematical model of foaming degree was established including the model parameters determined from the experiment data.
讨论熔渣发泡现象的实质，建立泡沫渣发泡幅度的理论模型，并结合实验数据讨论了模型参数。
The essential of the foaming phenomenon in molten slag was discussed, and mathematical model of foaming degree was established including the model parameters determined from the experiment data.
应用推荐