冲压，焊接钢班卓琴住房，单减少，双曲线。
Pressed and welded steel banjo housing, single reduction, hypoid.
此外，我们订购一些用于焊接钢的焊条和三角皮带。
Besides that, we'd like to order some electrodes for steel and v-belts.
两部分都为焊接钢件并经高精度加工中心加工而成。
Both are made of electro-welded steel and are submitted to an accurate working under extremely high precision machining centers.
焊接钢型滚轧链条。焊接钢牵引链。附件和链轮齿。
Welded steel type mill chains, welded steel drag chains, attachments and sprocket teeth.
各种连接细节的疲劳性能是焊接钢桥研究的热点问题之一。
Fatigue cracks initiated from various connection details are common problems in welded steel bridge structures.
冲压，焊接钢班卓琴住房，单减少，双曲面齿轮，比6.33：1。
Pressed and welded steel banjo housing, single reduction, hypoid gear, ratio 6.33:1.
结合郑州跨机场路高架桥，主要阐述了全焊接钢箱梁施工的监理措施。
Based on viaduct over airport expressway in Zhengzhou, this paper mainly expounds supervising measures about full-welding construction of steel box girder.
变截面焊接钢吊车梁疲劳裂缝主要是由于变截面处有很大的应力集中所产生的。
The main form and cause of fatigue failure of steel crane beam are analyzed first, and focused the welded steel crane beam.
重点论述了南环大桥四柱式桥塔结构、缆索体系、全焊接钢加劲梁、环氯沥青桥面铺装等关键技术。
The segment assembling connection is a key procedure during the construction of truss stiffening girder of long span suspension bridge.
采用HDPE分丝管索鞍，即将HDPE分丝管置于矩形焊接钢箱内，在分丝管外灌注高标号水泥浆的结构形式。
The cable saddle is a structure with its HDPE sleeves installed in a rectangular steel box and with the high-grade cement mortar grouted outside the sleeves.
住房建筑商可能会发现铝加工，因为它具有挑战性需要氩弧焊或米格进程，更难以超过CroMo或碳焊接钢使用相同的过程。
Home builders may find aluminum fabrication challenging as it requires a TIG or MIG process and is more difficult to weld than CroMo or carbon steel using the same process.
焊接钢桥结构持续损伤至破坏的过程可以从两方面加以分析：一方面要考虑此过程中能量的耗散；另一方面要考虑此过程中焊接部位损伤负向激励。
For the behavior of structure fracture, the dissipation of energy and the damage of passive encourage should be taken into consideration in the course of dynamic damage.
轮子旋转时需要承受巨大的和不断变化的压力，所以要使结构更坚固，钢的部分要用螺栓连接，而不是焊接在一起。
The wheel would need to withstand immense and constantly changing stresses as it rotated, so to make the structure more robust, the steel sections were bolted rather than welded together.
将不锈钢和普通钢焊接在一起是可能的。
平均剑身长达三英尺，剑体焊接精良，整个剑的主梁与剑刃由尖端的冶炼工艺锤锻而成，钢与铁按照完美的比例整合一体。
Averaging about three feet, blades were pattern welded, a sophisticated technique by which twisted rods and strips of iron or steel were hammered together.
结果表明，X80级管线钢在焊接过程中形成的热影响区由不同温度下形成的梯度组织组成。
The results indicate that HAZ produced during welding of grade X80 steel is made up of grads structure under different temperature.
将转接件分别焊接在埋件上及工字钢上，然后将立柱用螺栓与转接件连接起来。
Weld switchover pieces separately on embedment and I-steel, and then connect the mullion with bolts and switchover pieces.
用于铸铁碳钢不锈钢和低合金钢的焊接。
同锡线一起使用，焊接不锈钢等难以上锡的金属。
Used with the solder wire together, soldering a stainless steel etc metal.
硅量增加，会降低钢的焊接性能。
The increase of silicon will reduce the welding performance of steel.
还简述了X80管线钢对焊接的特殊要求。
The special requirement for the welding of X80 pipeline steel was described also.
用于相同强度等级的低合金高强钢的焊接。
For welding low-alloy and high strength steel with corresponding strength grade.
新的焊接工艺使不锈钢有可能广泛应用在石油工业中。
The new welding process has made possible the wide application of stainless steel in petroleum industry.
钢的焊接CCT图，是正确选择焊接材料、确定最佳焊接工艺、消除焊接裂纹、制订焊后热处理规范的重要依据。
Welding CCT diagrams of steels are the basic to select welding material, determine the optimum welding technology, relieve welding cracks and lay down standard of past heat treatment.
采用焊接热模拟技术和显微分析方法，研究了回火焊道热处理对X80级管线钢焊接热影响区韧性的影响规律。
The effects of tempering weld-pass treatment on toughness of HAZ of X80 pipeline steel were studied by the technique of welding thermal simulation and the method of microscope analysis.
没有钢铁公司比我们知道更多关于钢的选择，加工，抛光，焊接或铸造涂料，比如国际模具钢，让我们拥有了更多的客户。
No steel company knows more about steel selection, machining, texturing, polishing, welding or mold coatings, than International mold steel, just ask our customers.
本文就不锈钢复合板焊接中可能出现的问题以及在实际焊接中应采取的工艺措施进行了讨论。
In this paper, the problems which may encounter in welding are described and process measures taken in production welding are discussed.
本文就不锈钢复合板焊接中可能出现的问题以及在实际焊接中应采取的工艺措施进行了讨论。
In this paper, the problems which may encounter in welding are described and process measures taken in production welding are discussed.
应用推荐