冷冻水冷器各传热管冷却水量分布不均匀使其冷却效率普遍很低。
Cooling water is not distributed well in each heat transfer tubes which makes the operation efficiency of vertical water coolers low.
针对磨粉机在加工过程中磨辊温度的升高对面粉品质影响的问题，设计了旋转热管冷却式磨辊。
To solve the influence of grinder roll's rising temperature on the quality of flour during the working process of mill, the cooled type grinder roll was designed.
提出一种新型高效自蒸发循环旋转热管冷却技术来冷却连续混炼机的转子，并进行了模拟试验研究。
A new kind of high efficient self evaporating circulation rotating heat pipe cooling technique for the rotor of a continuous mixer has been proposed, and simulated test has been investigated.
详细地阐述了对气膜冷却、内部强化换热以及热管冷却等的影响因素，目前的应用状况以及发展前景。
This paper presented influence of factor on film cooling, enhanced heat transfer in tunnel and heat pipe cooling, how to apply and development for these technologies.
对充气热管空气预热器的结构进行分析和应用介绍，采用平界面模型，确定充气热管冷却段的有效长度。
By using a flat interface model it is possible to determine the effective length of a gas-filled heat pipe cooling section.
研究结果表明，采用自蒸发循环旋转热管冷却技术冷却连续混炼机的转子具有高效的导热性、良好的表面均温性、无泄漏等优点。
The rotating heat pipe cooling technique with self-evaporating circulating liquid for the rotor in continuous mixer was investigated by a simulating experiment.
研究热管结构对压铸模具冷却能力影响的定量关系。
The quantitative relation between hot pipe structure and cooling ability of partial die casting mould was approached.
自定义热管理配置也可用于数字视频录像机独特的冷却方式。
Custom thermal management configuration is also available for DVRs featuring unique cooling patterns.
本文提出了热管换热器加热段和冷却段的三种长度比：流通长度比、经济长度比和许用安全长度比。
Three kinds of length ratio of evaporator to condenser of heat pipe heat exchangers are proposed: the flow length ratio, the saving length ratio, and the allowable safety length ratio.
文中介绍一种利用工艺中液体冷却放出热量来加热气体的分离式热管换热器。
The paper introduces the separate type heat pipe exchanger to heat the gas from process liquid.
某厂油压机系统的两台油冷却器，在投入使用后不到一年的时间里(实际使用8个月)，发现换热管有泄漏现象。
Only after one year (actuary service period: 8 months) of use, the leakage occurred in the exchange tube of two coolers which were in a plant oil-compress system.
为了更高热传导性能，Noctua对冷却片焊接热管。
Noctua solders the heat pipes to the cooling fins in order to assist the heat conductivity.
通过对冷却水、传热管以及垢层的分析检验，发现氨冷凝器传热管泄漏是由冷却水对金属的电化学腐蚀引起的。
It was found that the leakage cause of the ammonia condenser tubes was the electrochemical corrosion due to the cooling water based on the analysis on the cooling water, tubes and the scales.
研究表明，微小矩形多槽道平板热管具有高传热特性，在电子器件冷却等方面有良好的应用前景。
The study indicates that the micro rectangle grooves flat heat pipe is characterized by high heat transfer capability with good prospects for cooling electronic components.
PEMFC的热模拟及软件开发是PEMFC模拟研究的两个重要方面，热模拟为PEMFC的热管理、冷却系统设计提供科学依据；
The thermal simulation and software development of PEMFC are two important aspects of studying PEMFC, which give a scientific guide and software supporting to the thermal management of PEMFC.
flexpipe-记忆体与冷却的热管。
设计了一种用于CPU冷却的集成热管散热器，介绍了其结构特点。
An integrated heat sink using heat pipes for cooling CPU is proposed in the paper. The structural characteristics are also introduced.
对第二工作相冷却工作物质的热管理模型进行了讨论。
A heat management mode for cooling the active medium in the second operating phase was discussed also.
通过一系列的实验，探讨了脉动热管的加热段长度与冷却段长度分配对其极限热输送能力的影响。
The results show that the unsteady area and heat transport ability of the diagram based on drift flux model are smaller than that of the diagram based on homogenous model.
2005年下一代热管理材料与系统会议文集。电子学与光子学中微尺度冷却的机遇挑战与技术解决方案，附光盘。
Next-generation Thermal Management Materials And Systems. Conference. 2005. Challenges Opportunities And Technology Solutions For Microscale Cooling In Photonics And Electronics (CD-ROM)
2005年下一代热管理材料与系统会议文集。电子学与光子学中微尺度冷却的机遇挑战与技术解决方案，附光盘。
Next-generation Thermal Management Materials And Systems. Conference. 2005. Challenges Opportunities And Technology Solutions For Microscale Cooling In Photonics And Electronics (CD-ROM)
应用推荐