研究了热时效对副复式不锈钢磁敏感性的影响。
The effect of thermal ageing on the magnetic susceptibility of a duplex stainless steel has been studied.
在调查分析的基础上，提出取消灰铁热时效的看法。
The production of gray iron casting without thermal aging was suggested.
用三维原子探针(3dap)和热时效处理方法研究压力容器模拟钢中富铜原子团簇的析出过程。
Three-dimensional atom probe (3dap) and thermal aged method were used to characterize precipitation of Cu-rich clusters in pressure vessel model steel.
得到3种时效处理方法的绿色性综合评分值分别为：振动时效66.8分、热时效56.8分、自然时效53分。
Green synthesis value of three aging treatments is obtained which respectively is: Vibration effectiveness 66.8, hot aging 56.8 minute, natural aging 53.
其处理效果优于热时效和传统振动时效，成为名符其实并可移动的应力消除炉，可取代以消除应力为目的的其它时效方式。
The treatment effect than traditional heat aging and vibration time, become a truly mobile stress relief furnace, can be replaced to eliminate the stress for the purpose of heat aging.
对不同焊接热输入下的6063铝合金焊接接头进行人工时效，分析其硬度分布和强度的变化。
Effects of artificial ageing on the hardness distributions and strength were analyzed for 6063 aluminum alloy joints welded by varying heat inputs.
与此同时还应用X射线小角散射技术和示差扫描量热仪等观测结构弛豫的手段测量了人工时效样品的相应现象。
The corresponding phenomena after the specimen was aged artificially was studied with the small Angle X-ray scattering and DSC, which are suitable for observing structure relaxation.
该平台成功应用于卫星热控系统的文档设计，极大地提高了设计工作的时效性和规范性。
The platform is applied to documents designing of satellite thermal control system successfully. It improves work efficiency and standardization greatly.
在测试了该集热器阵列的入射角修正系数的基础上给出了全日效率与瞬时效率的关系。
On the basis of the measured incident Angle modified coefficient of the collector panels, the relation between the daily and instantaneous efficiency is given.
通过实验，还分别测定了单根真空管和真空管集热器的瞬时效率曲线。
Instantaneous efficiency curves for both single evacuated tube and complete evacuated tubular collector are also tested.
对焊接接头进行人工时效后，不同热输入条件下得到的焊接接头的强度和延伸率都有明显提高。
After aging treatment, the strength and elongation of welded joints under different parameters increased and their mechanical properties were similar.
研究了含铜时效钢焊接热影响区的组织与性能。
The microstructure and mechanical properties of a copper bearing age hardening steel were studied.
利用差示量热法（DSC）、透射电镜（TEM）、选区电子衍射（SAED）、常规力学性能测试等手段研究了7B04铝合金时效沉淀析出及强化行为。
The ageing precipitation and strengthening behavior of 7B04 aluminum alloy were investigated by DSC, TEM, HREM, SAED and tensile testing techniques.
分析表明：峰值时效使热空位大量回复并使基体电子密度提高。
The analyses for lifetime spectra show that a large number of thermal vacancies are recovered and the bulk electronic density increases during the peak ageing process.
采用差示扫描量热仪（DSC）研究稀土6061合金及其基体合金材料的时效析出序列，采用金相显微镜观察了稀土6061合金及其基体合金材料的显微组织。
The precipitation procedure of 6061-La and 6061 alloy was studied by differential scanning calorimetry (DSC). The microstructure of 6061-La and 6061 alloy was observed by metallurgical microscope.
采用理论计算、热影响区最高硬度试验和小铁研试验方法研究了超低碳含铜时效钢的抗裂性。
Cracking resistance of ultra-low cabon Cu-bearing age-hardening steels was studied in this paper by computing, maximum hardness in weld heat-affected zone test and Y-groove cracking test.
采用理论计算、热影响区最高硬度试验和小铁研试验方法研究了超低碳含铜时效钢的抗裂性。
Cracking resistance of ultra-low cabon Cu-bearing age-hardening steels was studied in this paper by computing, maximum hardness in weld heat-affected zone test and Y-groove cracking test.
应用推荐