与将冷函数填入缓存相比，将热函数(也就是那些更常用的函数)放在一起可以更好地利用指令缓存。
Keeping hot functions together (that is, those functions that are used more often) results in better instruction cache use compared to polluting the cache with cold functions.
GCC还可以帮助将函数划分到热区和冷区。
GCC can also help to partition functions into hot and cold sections.
相反，热调用点(hot call site)更可能被内联，以使代码尽量短小，同时仍获得内联函数的优点。
Instead, hot call sites are more likely to be inlined to keep the code size small while still getting inline function benefits.
采用基于基本解方法和径向基函数插值的无网格算法(MFS- RBF)分析了广义的热弹性问题。
The method of fundamental solutions (MFS) with radial basis functions (RBF) approximation was developed for general thermoelastic analysis.
热工过程的动态数学模型通常通过现场试验作出它的阶跃响应曲线，然后从阶跃响应曲线得出近似传递函数。
In general, the dynamic math model of a thermal process is an approximate transfer function obtained from step response curve which is figured through field experiment.
多泵站多热站决定了输油管道优化运行的目标函数和约束条件的复杂性。
Multi-pump station and multi-heat station make the objective function and constrains of oil pipeline more complicated.
同步热分析法是一个比较精确的方法，其不但可以计算活化能而且可以同时求解反应级数和反应机理函数。
Simultaneous thermal analysis method is a relatively accurate method, it can not only compute the activation energy but also get reaction order and the conversion function at the same time.
通过定义接触面滑动屈服函数和流动势函数，得出了热接触边界的互补方程。
Through defining slide yield function and floating potential function of thermo-contact surface, the complementary equation of thermo-contact boundary was got.
本文用状态函数法导出无机化学中水合离子生成热绝对值与相对值之间的关系。
In the paper, it is given that the relation value between relative and absolute heat of formation of hydrated ions by state function method.
推导出热指数在工程应用中的拟合函数，并应用于电力负荷短期预测工作中。
The imitation function of heat index used in engineering applications is derived and applied to the short term electric load forecasting.
利用福克-普朗克方程的方法，讨论了RL回路中热涨落产生的电流效应，分析了噪声参数对电流定态几率分布函数的影响。
Using method of Fokker-Planck equation, effects of electrical current in RL circuit are discussed, and the effects of noise parameters on stationary probability distribution are analysed .
在超高真空条件下用热脱附和功函数变化等方法研究了氧在银-钡催化剂上的吸附和反应。
Under ultra high vacuum condition, the adsorption of oxygen and ethylene on electrolytic silver containing barium was studied by mass spectroscopy and work function change measurement.
用前向神经网络，对纯物质的蒸气压和汽化热与温度的函数关系进行预测。
A feedforward neural network was used to predict functional relationship of temperature with steam pressure and heat of vaporization of the pure material.
这种热残余应力可以表示为纤维、基体材料性质以及纤维束几何参数的函数。
The thermal residual stresses can be indicated as a function of the properties of fibers and matrix materials and geometry of twisted fiber bundle.
由此可使理想量子气体的热力学函数表示成统一的简洁形式，并进一步揭示了热波长的物理内涵。
It makes the thermodynamic functions of an ideal quantum gas may be expressed in a unified compact form, and the physical connotation of the thermal wavelength is revealed further.
以单位发电量最低成本为目标函数，建立了燃气-蒸汽联合循环发电系统的热经济学优化模型。
Taking the minimum cost per unit power generation as the objective function, a thermo-economic optimization model for gas and steam combined cycle power generation system is established.
文中使用径向基函数理论建立了基于RBF神经网络的数控机床热误差数学模型。
A neural network based on radial basis function (RBF) was used to predict and compensate the thermal error of a CNC turning center.
针对带钢热连轧双机架粗轧机组的特点，应用综合等负荷函数法进行负荷分配。
An aggregate equal load function was developed and applied to the load distribution on a double-stand mill during hot strip rough rolling.
根据等效焓降法在热力系统计算时的特点，推导了循环函数法在回热系统中的局部定量计算方法，导出了回热系统局部定量计算的几个重要结论。
According to the features of equivalent enthalpy-drop method applied to thermodynamic system, the methods of local quantitative calculation for cycle function method in regenerative system is deduced.
同时利用基于MATLAB环境下的径向基函数网络，建立了回热系统故障诊断模型。
Meanwhile, by utilizing a radial base-function network based on a MATLAB environment established was a fault diagnostic model for the regenerative heating system.
基于能量平衡方程建立了热烟气层轰燃模型，经量纲归一化和微分同胚变换，得到属于燕尾突变的势函数。
A catastrophe potential function, which has the same form of swallowtail catastrophe, was obtained by dimensional normalization and diffeomorphism.
采用统计学描述方法，从泊松分布导出的响应函数作为热释光剂量响应的基本方程，将线性、亚线性和超线性响应进行统一的描述。
It is assumed that a dose response function derived from the statistical poisson distribution can be used to describe the TL dose responses.
采用三维流函数法对棒材热连轧时的椭圆-圆孔型系统进行了力能参数的解析，其结果与实测结果符合很好。
Using three dimensional fluxional function, the rolling force and energy parameters of oval round pass sequences for hot continuous bar rolling were analyzed.
文中指出，在给定其它参数时，系统的总效率仅是集热器工作温度的函数。
It is found that the total efficiency of the system is a function of operating temperature of the collector with given other parameters.
针对C VC热连轧精轧机组板形计算问题，采用影响函数法开发了计算热连轧机轧后板断面厚度分布的软件。
As to the flatness calculating of CVC mill, a software is developed to predict the strip thickness distribution after rolling by using the influence function method.
文章在建立了热力系统加热器的通用性数学模型的基础上，用循环函数法对整个回热系统进行热力计算。
This article derives a general model of heater for thermal dynamic system. Based on the general model, the thermal parameters of regenerating system can be calculated by Circulating Function Method.
文中推导淬火炉的热传递函数，介绍了具有一定带宽的继电器特性控制方法和STD总线单片机系统的具体结构。
Transmit fuction of heat was derived in this paper, A method of controlling characteristic with some band width and the structure of the STD BUS microcontroller w…
文中推导淬火炉的热传递函数，介绍了具有一定带宽的继电器特性控制方法和STD总线单片机系统的具体结构。
Transmit fuction of heat was derived in this paper, A method of controlling characteristic with some band width and the structure of the STD BUS microcontroller was pre…
文中推导淬火炉的热传递函数，介绍了具有一定带宽的继电器特性控制方法和STD总线单片机系统的具体结构。
Transmit fuction of heat was derived in this paper, A method of controlling characteristic with some band width and the structure of the STD BUS microcontroller was pre…
应用推荐