桩基与土体间发生了脱开再闭合和滑移现象。
The phenomena of separation, reclosing and sliding occur between pile foundation and soil.
更为主要的是该模型还可以用于解释泡沫压裂液的屈服应力和壁面滑移现象。
Especially, this model can also explain the yield stress and wall slip phenomena for foam fracturing fluid.
本文主要采用分子动力学方法研究了滑移现象及其对亚微米尺度气体流动和纳米尺度液体流动的影响规律及其机制。
The present dissertation investigates the slip phenomenon and its effect on micro - and nanoscale flows by molecular dynamics simulation method.
随转速的增大，界面滑移现象对水膜压力和轴承承载能力的削减程度明显增大，水膜压力和轴承承载能力将降低50%左右。
With the increasing of the rotational speed, the water film pressure and the load capacity of the elastic-metal-plastic thrust bearing were reduced by 50%.
钛合金的切屑变形从低速起就是一种典型的集中剪切滑移，这种集中剪切滑移在高速切削大部分难加工材料时是一种普遍现象。
The chip deformation of titanium alloys is typical shear localization from low cutting speed, which is general phenomenon in machining of difficult to cut material at high cutting speed.
预紧接触式垫层结构中的预紧力是随系统的状态而改变的，在一定的振动环境下，会产生滑移、接触分离等现象。
The prepressing-force is changed by the state of the prepressing-contact cushion structure, and the slip phenomenon is appeared in the vibration environment.
壁滑移发生在口型出口附近。这种压力波动现象主要归因于试样的壁滑移行为。
This phenomenon of pressure oscillation can be attributed to the wall slip behaviour of the sample.
基于韧性单晶体实验现象，建立了描述晶体塑性变形的离散滑移模型。
Based on the experiment results of single crystals, a discrete slip model is established to describe the crystal plastic deformation.
分析了沥青混凝土路面面层产生滑移裂缝现象的原因，提出了在施工中应采取的控制措施。
This paper analyzes the reasons of the slumping cracks on the asphalt-concrete road surface, and advances some control measures that should be adopted in the construction.
与此现象相关的可能原因是初期的变形机制主要属马氏体片的自协作机制而不是一般的滑移机制。
The anomaly may be due to the self-accommodating mechanism of martensite plates in initially deforming, not the sliding, thus resulting in no increase of defects to which positron are sensitive.
采用双毛细管流变仪详细研究了聚乙烯及其共聚物的挤出畸变、管壁滑移及挤出压力振荡现象。
The effect of blending was investigated by analyzing the viscoelasticity, pressure oscillation, flow curves and extrudate appearance.
阐述了应力腐蚀和冲刷腐蚀机理，提出了适用于热轧钢卷强制冷却过程出现的应力腐蚀现象的滑移—锈蚀理论，可以很好地解释热轧钢卷冷却后出现的腐蚀缺陷。
Based on the stress corrosion, erosion mechanism and slippage-rust theory suitable to the stress corrosion of hot rolled coil during forced cooling, the coil corrosion defects are explained.
阐述了应力腐蚀和冲刷腐蚀机理，提出了适用于热轧钢卷强制冷却过程出现的应力腐蚀现象的滑移—锈蚀理论，可以很好地解释热轧钢卷冷却后出现的腐蚀缺陷。
Based on the stress corrosion, erosion mechanism and slippage-rust theory suitable to the stress corrosion of hot rolled coil during forced cooling, the coil corrosion defects are explained.
应用推荐