冶金、矿山等行业所用湿磨机衬板的服役条件十分恶劣,既要承受冲击,又要承受腐蚀和磨。
Lining board used in the wet-grinding machine at metallurgical mines works under very bad conditions. It has to bear impact, corrosion and wear.
把电阻线绕在无硷性耐热陶瓷件上,外面加上耐热、耐湿及耐腐蚀之材料保护固定而成。
Wire wound resistors are made by winding the resistance wire on the alkali less ceramic core, then coated with noncorrosice, heat-proof and humidty proof material.
低碳钢都使用环氧沥青层在其表面镀上湿膜,用以防止生锈或腐蚀。
Mild Steel reservoirs are coated on all wetted surfaces with a epoxy-tar layer to prevent rust or corrosion.
冶金矿山湿式磨机衬板,使用工矿条件恶劣,既受腐蚀又受冲击和磨损。
The liner of the wet-grinding machine at metallurgical mines works under very bad conditions, and it has to bear impact, corrosion and abrasion.
通过对湿式磨矿钢耗和腐蚀机理的分析,着重探讨了影响钢耗的一些因素。
In the present work, the principle of steel consuming and corrosion in the course of WMG have been analyzed, emphatically pointing out factors that affects steel consuming.
不能用湿拖把或有腐蚀性的液体(如肥皂水、汽油)擦拭地板。
Cannot use wet mop or mordant liquid (like suds, benzine) wipe a floor.
对于腐蚀性最弱的化学物质、湿的或干的有机酸、醇以及酮等流体介质,一般来说纯树脂橡胶表现还是好的。
Pure Gum Rubber is generally good for most weak chemicals, wet or dry organic acids, alcohols, and ketones.
介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法。
The standards and techniques for the corrosion test of metal materials in wet H2S environment are described. The problems normally encountered in the tests and solutions are highlighted.
针对水箱中高湿热腐蚀环境,介绍了涂层在热水、溶解氧及腐蚀性氯离子等影响因素作用下发生的鼓泡、脱落、湿附着力丧失等现象。
The bubbling, flaking, loss of wet adhesion and et al of the coating film occurred under the action of hot water, dissolved oxygen, corrosive chlorium and et al are introduced.
对湿式气柜的腐蚀原因进行了分析,并提出了防护措施。
The causes of corrosion of wet gas holder were analyzed and protection measures were suggested.
验收项目中,有一个耐湿试验分组,用来加速评定外壳的抗腐蚀性能及相应的质量可靠性能。
In acceptance tests, a moisture resistance test is used to evaluate the anticorrosion property of the package and its relevant quality reliability.
举例说明了国内炼油厂湿硫化氢环境中过程设备的腐蚀失效情况和采取的相关措施,对今后应该注意的问题进行了讨论。
The case was presented to describe corrosion failures of the process equipment in wet hydrogen sulfide service in domestic refineries and corresponding measures taken. The precautions were discussed.
针对压力容器设备在湿硫化氢环境中经常产生的应力腐蚀破坏,结合工作实践,讨论了在不同情况下压力容器用钢的选材要求。
Against pressure vessel wet H2S in the environment often stress corrosion damage, combing work practice, discussed in different situations steel pressure vessel in the selection requirements.
对炼油厂低压湿式螺旋气柜的腐蚀原因进行分析,结果表明:腐蚀主要是由H_2S和CO_2等酸性气体引起。
The analysis of the corrosion in refinery low-pressure fluid seal gas holder reveals that the corrosion is mainly caused by the sour gas containing H_2S and CO_2, etc.
对湿硫化氢环境中应力腐蚀开裂的相关问题,国内外许多学者己开展了大量的研究工作,并取得了一定的研究成果。
Both domestic and foreign scholars have been carrying out large-scale research on the problem of stress corrosion cracking in wet H2S environments, and up to now, certain achievements have been made.
生产上采用国外进口意大利fenzi公司油漆,镜背漆耐腐蚀耐湿防水。
Production companies using imported Italian FENZI paint, mirror back paint waterproof moisture corrosion.
除尘器适于常湿环境下有无腐蚀性的非纤维性粉尘的收集。
The utility model is suitable for collecting non-corrosive non-fibrous dust under normal wet environment.
除尘器适于常湿环境下有无腐蚀性的非纤维性粉尘的收集。
The utility model is suitable for collecting non-corrosive non-fibrous dust under normal wet environment.
应用推荐