肌肉注射或静脉注射与口服使用同一类型的药物，但在原则上，不应该注射的口服药物。
Intramuscular or intravenous injection: use the same type of drug with oral, but in principle, the oral drugs should not be injected.
注射死刑不平等适用违反了法律面前人人平等原则，引起社会的诸多质疑。
Unequal application of lethal injection violates the principle of equality in law, and has aroused many doubts.
阐述了气体辅助注射模具设计的一般原则，介绍了气针的工作原理和选择方法。
The general design principle of gas-assisted injection mould design is discussed. The working principle and selection method of gas pins are introduced.
对照组大鼠按照同期平行对照的原则，以相同方式注射同体积的生理盐水。
According to the parallel control principal, rats in the control group were injected with saline of the same volume with the same method.
方法：按照逐日递增原则给予小鼠皮下注射吗啡，以纳洛酮催瘾，建立吗啡戒断后焦虑动物模型。
Methods: The anxiety mice model was formed based on the principle of morphine increase progressively day by day, in which after the mice were induced into morphine dependence, naloxone was given.
这些原则我会在下一节给出，该节会讨论口服类固醇和注射类固醇的区别。
This will be covered in the next section which will describe the difference between orals and injectables.
作为原则，注射速度应越快越好。
As a rule, the injection speed should be the faster the better.
进一步提出了实例库的设计原则与组织原则，建立了塑件和模具之间的E -R模型，提出了注射模实例的分散组织存储方法。
Further more, rules of case library designing, organizing and distributed storing are investigated, in which, an E-R (Entity-relation) model of plastic parts and injection mould is constructed.
研究了注射模各种型腔排气系统的设计原则、要点、结构及其应用范围和优点。
The design principle and key points, mould structure and range of application were researched as well.
首先介绍模具的类型及其基本结构，模具与注射机注塑模具毕业设计之间的关系，接着说明模具设计的一般原则以及在设计时要注意的一注塑模具毕业设计些问题。
First, introduce the types and basic structure of the mold, the relation of the mold and the injection machine, then elaborate the usual principles of mold design and some problems during design.
结合经络理论及神经治疗原则，以经络注射液为注射内容的的“神经-经络”水针疗法结合手法对神经根型颈椎病相对单纯手法治疗更为有效。
CONCLUSION Guiding by the principle of TCM meridian theory and Nervestem Stimulation Therapy, using "meridian injection with tuina, the Neuro-meridian therapy is more effective in treatment of CSR."
介绍了精密注射成型的特点，阐述了精密注射模排气系统的各种设计方法 ，特别是分型面上排气槽的开设原则和设计工艺参数。
New injection molding technologies including precision injection molding technology are developing with the requirements of high quality of injection molding parts.
介绍了精密注射成型的特点，阐述了精密注射模排气系统的各种设计方法 ，特别是分型面上排气槽的开设原则和设计工艺参数。
New injection molding technologies including precision injection molding technology are developing with the requirements of high quality of injection molding parts.
应用推荐