到目前为止，普通烙铁的焊嘴主要还是是铜，为了防止氧化，铜已经被处理加装铁皮或电镀。
So far, soldering iron tips have been made mainly of copper, and in order to prevent oxidization, the copper has been either iron-plated or chromlum-plated.
其次，本文研究了钎缝中未焊合、孔洞、夹渣、溶蚀以及金属间氧化物等缺陷的产生原因及控制因素。
Thirdly, the causes of defects and the controlling factors of the seam such as gap, porosity, slag, corrosion and metal oxides was discussed in this paper.
公司具备电焊、二氧化碳气体保护焊、氩弧焊、碳弧气刨、氧气切割等特种作业人员。
Companies with welding, carbon dioxide gas shielded arc welding, argon, carbon arc gouging, oxygen cutting and other special operations personnel.
焊接采用二氧化碳保焊连续焊缝，型腔全密封，耐腐蚀。
Welding using carbon dioxide welding continuous welding seam, cavity seal, corrosion resistance.
粉末火焰喷涂喷焊设备。用惰性气体送粉，能得到更佳涂层品质，也可喷涂氧化物涂层。
Powder flame spray or spray fusing gun can be used with inert gas to feed powder with best coating effects and can also be used for spary of ceramic powder.
经表面氧化层处理后，焊料表面粗糙度的降低引起低剪切速率下焊膏粘度的明显升高。
After surface oxide film treatment, the increase of viscosities at low shear rates results from the decrease of surface roughness on the surface of solder powders.
基层的焊接，推荐采用手工电弧焊、埋弧焊以及二氧化碳气体保护焊。
Shielded Metal Arc Welding, Submerged-arc Welding and CO2 Arc Welding are recommended for base layer welding.
电弧焊、二氧化碳气体保护焊、氩弧焊等各种焊接。
Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc.
介绍了为解决二氧化碳气体保护焊焊丝锈蚀问题而研制的表面防锈剂的性能及其在生产上的应用。
The paper describes the performance and production application of the surface rust preventer developed to protect the CO2 shielded arc welding wires from rusting.
我是电焊工，从事手工电弧焊和二氧化碳气体保护焊工作，通过…
I am, electric welders engaged in manual arc welding and carbon dioxide welding work, through these years of electric welding work my technology …
对二氧化碳气体保护焊镀铜焊丝进行了缓蚀处理试验。
In this paper, the inhibition treatment of the copper plating wire used in co 2 gas shielded arc welding is dealed with.
利用二氧化碳保护焊、埋弧焊、手工电弧焊研究了高强度贝氏体钢板焊接接头的组织和力学性能。
The joint microstructure and mechanical properties of high strength bainitic steel plate were studied by CO2 gas shielded welding(CGSW), submerged arc welding(SAW) and manual arc welding(MAW).
该工艺是两种金属之间直接熔接，焊点美观牢固，没有锡焊引起的脆裂、氧化、虚焊、假焊。
The process is directly between the two types of metal welding, a solid solder joint appearance, there is no brittle fracture caused by tin solder, oxidation, solder false.
焊后，身体是腌制-一个过程，使用非常corrisive的氨基酸组合，以消除黑暗氧化铁焊缝附近地区形成了焊接过程中的热量。
After welding, the body is pickled — a process that USES a very corrisive mix of acids to remove the dark iron oxides formed near the weld area by the heat of the welding process.
焊后，身体是腌制-一个过程，使用非常corrisive的氨基酸组合，以消除黑暗氧化铁焊缝附近地区形成了焊接过程中的热量。
After welding, the body is pickled — a process that USES a very corrisive mix of acids to remove the dark iron oxides formed near the weld area by the heat of the welding process.
应用推荐