该系统可以实现对气缸位置的高精度控制。
在飞轮前端面有一浅凹口，其用来确定第一个气缸中活塞的位置。
In the front face of the flywheel, there is a shallow indentation used to determine the position of the piston in the first cylinder.
百分表及通用百分表托架必须通过螺钉固定在气缸体上，位置与曲轴臂相对。
Dial gauge with universal dial gauge bracket must be screwed to the cylinder block and placed against the crank arm.
检查气缸上前后磁簧开关的位置。
Check the position of the rear and front magnetic reed switches on the cylinder.
点火正时装置：触点必须能够在活塞处于气缸中相关位置时，按时关闭和开启。
Ignition timing devices. The contact points must be timed to close and open in proper relation to the piston positions in the cylinders.
气动脉宽调制位置伺服系统是非线性的系统，在气缸摩擦力较大的情况下，采用传统的控制方法难以取得满意的效果。
Pneumatic PWM position servo system is nonlinear system. The satisfied results are difficult to be obtained with traditional control method while the friction force of cylinder is large.
介绍了一种适用于测量气缸体上各孔位置及任意两孔间距离的专用测量工具。
This paper Outlines a special gauge suitable for measuring the hole positions or distance between two holes in the cylinder blocks.
在先磨削不同厚度的玻璃时，磨头可利用其气缸快速升降，以迅速改变磨轮位置或更换砂轮。
When grinding glass with different thickness, the wheel head can be raised or lowered fast with the air cylinder to change its position or change the heads.
在使用叶片式风速仪测量模拟气缸内的涡流转速时，分析叶片形状、安置位置可能带来的影响；
When the blade type anemograph is used to measure and simulate the turbulence speed, the effect involved possibly by the blade shape and installation position is tested.
此外，农民自卫队系列有利于凡在气缸行程和速度的变化要求或申请的位置连续监测要求。
Additionally, the ACCU Series is conducive where variations in cylinder stroke and speed are required or where an application calls for continuous position monitoring.
本文对由伺服阀和无杆气缸组成的气动伺服位置控制系统进行了数学建模和控制研究。
The pneumatic servo positioning system, which is composed of rodless cylinder and the servo valve, is studied on mathematical modeling and control in this paper.
曲轴上凸轮凸角的位置使气门在恰当的时侯开关，以便与气缸的工作顺序相一致。
The CAM lobes are so positioned on the camshaft as to cause the valves to open and close in the cylinders at the proper time with respect to the actions taking place, in the cylinders.
本文就16240Z型柴油机气缸盖的裂损情况作了分析，指出不同位置裂纹的起因。
This paper describes the analysis of the cylinder head cracks on 16240Z type diesel engines and discusses the originated cause of these cracks created at different locations.
另外，还对不同怠速转速、不同怠速空气螺钉位置及不同气缸盖温度对排气排放的影响进行了探讨。
In addition, the influence of different idling speeds, different positions of idling air screw and different temper...
该文对三通比例流量阀控制的摆动气缸转角位置伺服系统进行研究。
A pneumatic rotary actuator angular position servo system is studied, which adopts 3-port proportional flow valve as a control device.
升降装置由气缸控制， 该气缸有两个停止位置，可使产品码成四包；
The lifting component is controlled byan air cylinder, the products can be stacked into four packs as the air cylinder is provided with two stopping positions;
因为凸轮轴位置传感器能够识别哪一个气缸活塞即将到达上止点，所以称为气缸识别传感器。
This sensor can also indicate which cylinder will reach to tope dead center, so it 'also called cylinder indication sensor.
因为凸轮轴位置传感器能够识别哪一个气缸活塞即将到达上止点，所以称为气缸识别传感器。
This sensor can also indicate which cylinder will reach to tope dead center, so it 'also called cylinder indication sensor.
应用推荐