标准雨刷是由发动机歧管内部驱动。
The standard wiper was driven by intake from the engine manifold, which was connected by a series of hoses to the wiper motor.
废气经另外一个排气歧管排出。
清洁排气歧管和汽缸头配合面。
Clean the exhaust manifold and cylinder head mating surfaces.
压缩空气注入在左端进气歧管管。
Compressed air is injected at the left end of the intake manifold tube.
废气经另外一个排气歧管排出。
废气经另外一个排气歧管排出。
进气歧管把发动机进气道口连接起来。
The intake manifold connects the carburetor to the intake ports of the engine.
在压缩机歧管配件里安装高压释放阀。
Install the high pressure relief valve in the compressor manifold fitting.
拆下螺栓并举高盘脱离歧管。扔掉衬垫。
Remove the bolts and lift the pan off the manifolDiscard the gasket.
电磁先导阀可在基地安装和歧管安装结构。
Solenoid pilot operated valves available in sub-base mount and manifold mount constructions.
注塑成型工艺是开发塑料进气歧管的重要环节。
The injection molding is an important tache to exploit plastic air intake manifold.
废气从排气歧管流入排气管，进入催化转换器。
The exhaust gas flows from the exhaust manifold into an exhaust pipe and from there into the catalytic converter.
目前，国内设计制造塑料进气歧管的技术还不过关。
针对国内目前还不能自主设计塑料进气歧管注塑模具。
Aim to be not able to design mould of plastic air manifold by domestic technique.
和心脏的引擎是一种欺骗排气歧管和双双卷轴涡轮增压器。
And the heart of this engine is a trick exhaust manifold and a pair of twin-scroll turbochargers.
活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。
The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
我们生产了一种特殊的设施-歧管-用于填充和运输设备。
GasFlo Products fabricates a unique offering of manifold systems for filling and delivery applications.
如果发动机回火，进气歧管骤增的压力就迫使阀门向后移动。
If the engine backfires, the sudden pressure in the intake manifold forces the valve back.
总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。
Summarized some important experience on designing injection mould of plastic air intake manifold.
这是因为当发动机熄火时，进气歧管冷却而产生轻微的真空。
When the engine is shut off, the intake manifold cools and a slight vacuum forms as a result .
这种装置称为“歧管热控制阀”，它拼装在排气与进气歧管中。
This device, called the manifold heat-control valve, is built into the exhaust and intake manifold.
检查两个管的末端，排气歧管和EGR阀是否有泄露或表面有裂痕。
Check for signs of leakage or cracked surfaces at both ends of tube, exhaust manifold and EGR valve.
出口软管接连发动机歧管，内口软管接入仪器板，并连接至一个小盘表。
The outlet hose ran to the engine manifold, and the inlet hose ran to the dashboard, where it was attached to a small dial.
介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。
This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.
尼克拿过来一根螺栓套杆，把一头儿贴在进气歧管上，然后凑过去听了听另外一头儿。
Nick set one end of a long socket extension on the intake manifold and listened to the other end.
本文主要进行可变式进气歧管的三维曲面重建和空气流动模拟分析的研究。
This thesis mainly carries on research of three dimensional surface reconstruction of variable intake manifold and air fluid simulation analysis.
介绍了以快速原型技术和精密铸造技术进行进气歧管铸造模具制造的情况。
The situation of mould manufacturing for inlet manifold in rapid prototyping and investment casting was introduced.
介绍了以快速原型技术和精密铸造技术进行进气歧管铸造模具制造的情况。
The situation of mould manufacturing for inlet manifold in rapid prototyping and investment casting was introduced.
应用推荐