利用计算机模拟，附以现场的观测调查，可以对边坡的稳定情况做出较为准确的判断，并节省大量的人力和物力。
With the simulation and the survey on-spot, we can get the exact status of stability and retrench much manpower and material resources.
电力工业仿真机可以模拟现场生产实际情况，对运行人员进行反复培训，提高其业务素质。
The simulator for electric power industry can emulate practical condition of field production and train the operators repeatedly to enhance their operation capability.
介绍了ZY F型钻孔液压封孔器的研制、实验室模拟试验及现场工业性应用试验情况。
The development, lab analog test and field test of Model ZYF hydraulic hole packer are presented in the paper.
经模拟试验和现场应用情况表明，研制的液气分离器脱气效果良好，能满足欠平衡钻井需要。
The simulation test and field use show that, the new separator has good performance in separating gas from drilling fluid, it can meet the demand of underbalanced drilling.
同时根据现场情况及模拟结果，对C区边坡失稳提出卸载及加固方案。
The unloading and consolidation scheme for the instable slope in Section C is proposed based on the site condition and simulation results.
通过现场实测、相似模拟和数值计算得出了大倾角临界角煤层回采巷道塑性区的分布情况。
Through the site observation, the simulation and the numerical value computation, obtained the gateway plastic area in high-pitched and critical Angle seam.
方法应用系统抽样法进行现场查螺，现场和实验室模拟水淹实验观察钉螺存活情况。
Methods Systematic sampling method was used in field Oncomelania investigation, and laboratory and field simulating drowning methods were also performed to observe survival of Oncomelania.
结合湛江港某码头工程基桩，用模型试验模拟现场地质情况，对港口单桩、排架桩基负摩擦力进行模型试验。
The test of negative skin friction along the single pile or wharf bent piles, which is modeled after piles of ZanJiang harbor, is studied.
以现场稠油生产井为例，对软件所采用的数学模型进行了检验，模拟计算结果符合实际情况。
Take heavy oil production Wells as an actual example to test the mathematical model used in the software, the simulation results consistent with the actual situation.
本论文主要阐述利用计算机的集成思想，结合热轧工艺，来开发模拟轧钢功能，以及利用模拟轧钢进行现场各种情况的模拟测试。
Combined with technological process of hot strip rolling and using concept of computer integration, development of simulator system is described. The system is tested in site under various conditions.
采用电子模拟传感器输出信号的方法不能将温度传感器的测量滞后、故障以及使用现场的噪声等情况反映出来。
For traditional simulation methods, which simulate the output of temperature sensor, measurement lag, fault and the environment noise of temperature sensors can't be considered.
采用有限元方法，对某钢厂的大方坯连铸机的凝固传热情况以及坯壳凝固生长进行了数值模拟，并通过现场数据对模型进行了验证。
A finite element method (FEM) model is established to analyze the solidification heat transfer and shell growth of the old bloom caster in a steel works and is tested by the measured data.
在实验室条件下，模拟了聚合物注入现场情况以及垢样生成过程，研究了SZ36 - 1注聚井注入堵塞程度和范围。
For the indoor lab experiments, in ground condition, the polymer injection process and the formation process are to study the extent and scope of SZ36-1 injection well plugging.
在实验室条件下，模拟了聚合物注入现场情况以及垢样生成过程，研究了SZ36 - 1注聚井注入堵塞程度和范围。
For the indoor lab experiments, in ground condition, the polymer injection process and the formation process are to study the extent and scope of SZ36-1 injection well plugging.
应用推荐