电路元器件包括热电阻和热电容组成的重复单元被安置成为一个梯形电路。
The?circuit elements were arranged in a 'ladder circuit' comprising repeating units of thermal resistors and thermal capacitors.
如果能适时地引入梯形电路的简单介绍，则rc移相式振荡电路的振荡频率及振荡条件可以容易地求出。
If we introduce the ladder-shaped circuit simple in good time, the oscillating frequency and oscillating condition of rc phase shift oscillating can be w.
如果能适时地引入梯形电路的简单介绍，则rc移相式振荡电路的振荡频率及振荡条件可以容易地求出。
If we introduce the ladder-shaped circuit simple in good time, the oscillating frequency and oscillating condition of rc phase shift oscillating can be worked out easily.
设计中，采用了一种规则的全NMOS管构成的M-2M梯形电路，以及本文提出的电流-电压转换电路。
A regular NMOS-only M-2M ladder and a current-to-voltage conversion circuit proposed in this paper are adopted in this design.
提出了一种求解双交错梯形电路色散特性的新方法：腔场平均法，验证了此方法的正确性，并进行了数值计算。
A new method to ascertain the dispersive equation of the double staggered circuit, a cavity field average value method, is advanced. Its correction is verified.
设计了PLC控制PET生产过程中混料装置的硬件电路和控制系统的梯形图，阐述了程序的启动和运行过程。
Designing the hardware circuit and trapezoid drawing of the material mixing equipment for the PET producing process using PLC controlling system, introducing the starting and operating process.
该电路具有LC梯形的通带内元件变化的低灵敏度特性。
This circuit has low element change sensitivity within its LC ladder filter.
由于该系列PL C解算梯形图流程的特殊性，容易引起控制电路中电气联锁环节的失效。
Owing to the peculiarities of the PLC Ladder Logic graphic, there may well be the possibilities of the invalidation in the electric chain lock on the circuit.
介绍了用PLC改造旧设备时，根据继电器电路图设计梯形图的方法与步骤，并介绍了设计中需要注意的问题。
This paper introduces the approach and method of design of PLC ladder diagram based on relay diagram in old equipment alteration, some problems in design are discussed.
测试平台系统的动态力发生装置是利用激振器作为执行器并配以相应信号发生电路和功率放大器来实现梯形动态力。
The dynamic force generator is based on the vibration exciter which is used as the actuator to get the needed dynamic force with the corresponding signal generator and power amplifier.
介绍了一种对定时器、计数器、数据寄存器的数据进行外部设定并显示的电路，并给出了相应的梯形图程序。
This paper introduces a circuit setting up and displaying the data of timer, counter and data register out of PLC. It gives the ladder-type Patterned program.
文中采用等效电路法计算了单交叉梯形慢波电路的匹配特性。计算结果与实验测量基本一致。
Matching characteristics of single staggered ladder slow wave circuit are calculated by eguavelent circuit method in the paper.
工作台的控制要求，PLC控制电路和接线，参数设置内容及方法。重点叙述了PLC梯形图的编制过程。
This paper describes the control requirements of the CNC table, PLC control circuits and wiring, the content and methods of parameter set, and describes the process of preparing the PLC ladder.
工作台的控制要求，PLC控制电路和接线，参数设置内容及方法。重点叙述了PLC梯形图的编制过程。
This paper describes the control requirements of the CNC table, PLC control circuits and wiring, the content and methods of parameter set, and describes the process of preparing the PLC ladder.
应用推荐