采用静态校验法，成功地获得了氮气的排放份额。
The nitrogen discharge fraction is obtained by means of static calibration method.
四是本文采用三种检验方法，即自身检验法，交互校验法和预测值检验法，对财务危机预警模型进行有效性检验。
Finally, this paper adopts three different methods to test the validity of financial crisis warning model, that is self-validated, cross-validated, and forecasting-validated.
本文提出了在比较法水表校验装置上采用单片微机进行信号分析和数据处理的方法。
This paper presents a method of signal analysis and data processing using a single chip microcomputer in the contrast method of water meter calibration facility.
该系统利用电加热法对热电偶的时间常数进行在线校验，同时还可进行温度测量。
Time constant of thermocouple is checked on line with an electric heating method, and with the same thermocouple temperature is measured.
在软件部分首先介绍了整个系统的工作流程，然后对两项关键技术：循环冗余校验(crc)法和防碰撞法进行了阐述。
In the software part, the working flow of the system is introduced first. And then the two key technologies, Cyclic Redundancy Check (CRC) method and Anti-Collision method are presented.
使用标准表法对系统进行了实流校验，初步实验结果表明样机精度达0.5%。
The system is calibrated using the standard meter method. The experimental result shows the precision of the prototype is 0.5%.
这里首先分析了CRC校验软件的模型，在CRC - 16多项式下、采用查表法完成了其软件设计。
After analyzing software model of CRC firstly, software design is accomplished through looking up table in CRC-16.
理论证明，利用红外波长测温法测得的三个温度值具有互校性，可用来校验绝对黑体，并为红外测温提供了一种全新的方法。
The theory proves three temperatures measured through infrared wavelength thermometry are consistent, they can be used to verify the black body, and it provides a new met...
利用有限元法分析床身变形，校验了机床刚度。
A flexible finite element stiffness model of lathe bed is presented and analysed.
通过误差分析及湿度探针的校验表明双区加热法测量蒸汽湿度能够满足测量的要求。
The double region heating method is suitable for monitoring wetness fraction of steam turbine exhaust on line, which is proved by the error analysis and the calibration of wetness probe.
然后是用F—统计量法对物流节点类型确定的聚类结果进行校验，分析其聚类效果是否满意，合并是否合理。
Thirdly, use F-test to analyze whether the results got by the method forward used are satisfactory and reasonable or not.
最后，提出了三种方法对模型进行校验，分别是指标对比法、参数对比法、曲线拟合法。
Finally, three methods have been proposed for model calibration, namely, index comparison, parameter comparison and curve fitting.
经校验的逼近法随后应用于具体的三维应力下力的模型中。
The verified approach is then applied to the strength model of concrete under triaxial stresses.
采用这一方法构造的低密度校验码具有良好的结构。
The low-density parity-check codes constructed by the proposed method have a good structure.
未校验分类法类型适用于那些不需要由uddi来实施对某一个校验服务特别调用的那些类别和标识符。
Unchecked taxonomies are used for categorization and identification without the need for UDDI to perform a specific call-out to a validation service.
未校验分类法类型适用于那些不需要由uddi来实施对某一个校验服务特别调用的那些类别和标识符。
Unchecked taxonomies are used for categorization and identification without the need for UDDI to perform a specific call-out to a validation service.
应用推荐