当(螺柱)直接焊于母材时,严禁母材厚度薄于螺柱直径的1/3。
When welding directly to base metal, the base metal shall be no thinner than 1/3 the stud diameter.
采用差示扫描量热(dsc)法对微胶囊的壁材厚度和含量进行计算。
The content and the thickness of the microcapsule wall were obtained by using DSC analysis.
干燥后板材的含水率在材堆内分布均匀,在板材厚度方向分布有一定差异,平衡后可以使用;
However, a moisture content gradient occurred along the thickness direction but could be (balanced) after about a week.
结果显示,一定的母材厚度和焊后热处理条件,使熔合线附近氢浓度峰值提高,从而使氢剥离倾向增大。
The results show that certain thickness of the base metal and the regime of heat treatment will increase the peak hydrogen concentration and promote the tendency of disbonding.
针对目前冷轧生产中因轧辊偏心引起带材厚度波动的问题,提出了一种提高轧辊偏心信号频谱分析精度的方法。
Aiming at strip thickness fluctuation presently caused by roll eccentricity in cold rolling, a method of improving precision in spectrum analysis is proposed.
打磨焊缝表面缺陷或机械损伤后的厚度小于母材的厚度。
Seam surface defect after grinding or thickness is lower than base material after mechanical treatment.
结果表明:处理材的厚度吸湿回复率为2.68%,具有良好的尺寸稳定性,说明压缩变定效果好。
The result showed that the treated wood had good dimension stability, and the moisture Absorption recovery ratio of thickness was 2.68%, which indicated that the set of compression was almost fixed.
研究了所制备薄膜的厚度、颗粒度等与薄膜制备过程中激光脉冲频率、引弧电压和靶材—衬底间距等工作参数之间的对应关系。
We studied the relationship between the films thickness, grain size and deposition parameters, i. e. pulse laser frequency, striking voltage and distance from the target to the substrate.
山毛榉(山毛榉属)材,经纵锯或纵削、平切或旋切,不论是否经刨平、砂磨或端接,其厚度超过6公厘者。
Beech wood (Fagus SPP.) sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or finger-jointed, of a thickness exceeding 6 mm.
为了满足汽缸垫稳定的压缩、回弹性能要求,应注意复合板的厚度公差和柔性石墨面材最佳的密度范围的控制。
In order to meet steady compression -resilience properties as cylinder gasket, the thickness tolerance of composite sheet and the density of flexible graphite plate should be control.
利用D-T模型考虑了界面位借间的相互作用,计算了外延层与材底为不同失配、不同厚度时,应变的释放。
In this paper, we calculate the strain relaxation in the epilayer with various thickness and mismatch, using D-T model.
工业纸板生产设备主要用于压制各种规格幅面及厚度的工业灰、白纸板、护板纸板、鞋材纸板、绝缘纸板等。
The cardboard press machine used to suppress various specifications format and thickness of industrial ash, Paperboard, cardboard sheeting, cardboard footwear material, such as insulating cardboard.
本文针对异步恒延伸轧制的原理和带材纵向厚度精度的变化规律进行了研究;
The principle of the elongation asynchronous rolling and the pattern of lengthwise gauge variation of strips have been studied.
考察了宽幅机头对于不同厚度片材的挤出适应性,得到结论:当生产不同厚度的片材时, 阻尼块高度需要调整。 关键词:高分子防水卷材,三维有限元,流场分析,挤出机,机头。
As far as the practicability of the die for the thickness, the height of the block would be adjusted when extruding the sheets with different thickness.
厚度控制系统的稳定性直接影响着铝板带材的厚度控制精度和成品率。
To produce aluminum strip with high precision thickness, various control technologies should be coordinated synthetically.
厚度控制系统的稳定性直接影响着铝板带材的厚度控制精度和成品率。
To produce aluminum strip with high precision thickness, various control technologies should be coordinated synthetically.
应用推荐