所得的服务器选择条目如图19所示。
The resulting Server Selection entries are shown in Figure 19.
它专门设计用于改善服务器选择、负载优化和容错。
It is designed to improve server selection, load optimization, and fault tolerance.
为应用程序服务器选择合适的平台将决定可使用的工具。
Selecting the right platform for the application server will dictate the tools available to work with.
具体的方式各不相同，取决于您的应用程序服务器选择。
How you'll do this will vary, depending on your application server of choice.
服务器选择从数据库的东西，然后将它发送回客户端。
The server selects stuff from the database and then sends it back to the client.
请为您的本地服务器选择一个服务器范围，然后单击new。
Select a server scope for your local server, then click New.
本文简要分析了现有的服务器选择算法，指出其优点和缺点。
The existing server selection algorithms are briefly reviewed and both advantages and disadvantages of these algorithms are described.
服务器选择什么gzip文件基于键入，但是通常在他们决定压缩太限制。
Servers choose what to gzip based on file type, but are typically too limited in what they decide to compress.
从服务器选择框中选择node1：server1，很可能存在默认的选项。
From the server selection box, select node1: server1, which will likely be selected by default.
在Step2面板(图6)上，为目标服务器选择RemoteCluster。
On the Step 2 panel (Figure 6), select RemoteCluster for the target server.
结果还表明最小延迟服务器选择可以明显地提高请求接受率与降低启动延迟。
It is also show the minimal latency server selection can improve the request acceptance rate and decrease the startup delay.
每个方法都有优点和缺点-当为你的服务器选择一种方法的时候，要牢记流量和对服务器的需求。
There are advantages and drawbacks to each method - while choosing the method for your server, be sure to keep in mind traffic and its demands on the server.
基于OPC标准的EPA数据服务器选择OPC标准作为上层接口，选择EPA规范作为底层接口。
OPC Standard is selected as upper layer interface in contrast with EPA Specification as bottom layer interface in EPA Data Server based on OPC.
将自动测试作为每个构建的一部分，并且使用同样的服务器选择机制，将代码展开到那些拥有正确配置的机器上面。
Make automated tests a part of every build and use the same server selection mechanism to deploy the code onto machines that have the correct configuration for the tests.
对象的多个副本散布在网络的不同位置，网络骨干费用昂贵，不能只采用节点负载作为服务器选择的依据。
The node load is insufficient for the server selection because the multi-replica scatter at different place and the backbone is expensive.
服务和服务器端jazzAPI的语义与应用程序服务器选择无关，从而允许在将来版本中支持更多的应用程序服务器。
The semantics of services and server-side Jazz APIs are independent of the choice of application server, allowing additional application servers to be supported in future releases.
为了支持上述特性，我们提供了一个恢复服务器选择通知(recovery server selection notification)以及失败防护支持。
To support this, we provided a recovery server selection notification along with failure fencing support.
在服务器设置字段，选择默认的国家和时区。
In the Server Settings field, select your Default country and Default time zone.
这里只需配置服务器信息和选择目标表。
You only need to configure the server info and select the target table.
还可以基于服务器硬件选择可靠性级别。
You can also select levels of reliability based on the server hardware.
从服务器列表中选择使用的应用服务器。
Select the name of the application server being used from the list of servers.
为模板服务器名称选择local。
如果不是这样，请右键单击该服务器并选择Start。
步骤4：将模块映射到应用程序服务器，选择Next。
右键单击服务器并且选择Start(图6)。
右键单击新服务器，并选择Start。
为此，右键单击该服务器，选择Start。
从下拉列表中对服务器名字选择hostname \instancename。
Select hostname \ instance name from the drop-down list for a server name.
对于服务器，选择
如果要在一个域内配置多台服务器，可以选择一台将部署连接池的服务器。
If more than one server is configured in a domain, select a server to which the connection pool should be deployed.
应用推荐