最大应力出现在横截面上v为最大的地方。
The greatest stress is found at the location on the cross section where V is the largest.
疲劳寿命与最大应力近似呈对数线性关系。
The fatigue life was linear to the logarithmic maximum stress.
最大应力产生在小带轮的整个“静弧”上。
The greatest stress is produced on all"the static arc"of small belt pulley.
结果：1游离末端基牙远中牙颈部为最大应力区。
Results: 1 The greatest stress was in distal tooth neck area.
不过，这个方法可以非常有用的一个简单的识别的最大应力区。
However, this method can be very useful for a simple identification of maximum stress areas.
结果表明受风载荷的雷达罩的最大应力发生在截球底座的边界上。
The results showed that the maximum stress was located in the ground circle of the radome.
首先给出了半管加热管及壳体的弯距、剪力及最大应力计算公式。
In this article, it shows formulas to calculate bending moment, shear strength and maximum stress of heat tracing pipe and shell body.
种植体界面骨组织的最大应力位于种植体颈部周围的骨皮质界面；
The value of stress peaks in implants and in bone -implant interface under oblique loads appeared higher than those under vertical loads.
刚开始加载时，最大应力集中在搭接面以下的一个三角形区域内。
At the beginning of loading, the major principal stress centralize in a triangle area under the lap.
最大应力和最小应力或二者之一和平均应力，以确定其起伏程度。
Either the maximum and minimum stresses of one of these and the mean stress-are required to specify the fluctuation.
天然牙集中斜向载荷下最大应力值大于分散斜向载荷下的最大应力值。
On the tooth, stress under concentrated oblique loading was bigger than under dispersed oblique loading.
计算结果表明，整个球罐的最大应力发生于球罐底部的凸缘开孔的周边。
The numerical result shows that the maximal stresses of the whole spherical tank locate at the edge of the bottom's flanged opening.
十字轴最大应力发生在圆弧过渡处，因此，应提高该处的表面加工质量。
The maximal stress in cross universal coupling happens at the circular transition where measures should be taken to enhance the surface machining quality.
螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；
The max stress and the max radial displacement of conveyor is also proportional to the square of rotational speed.
物料离心液压引起的最大应力和最大径向位移都随着转鼓壁厚的减小而增大。
With the decrease of thickness of drum wall, the maximum of stress and radial displacement created by materiel pressure increase.
最危险点在接头的第一啮合齿的齿根处，最大应力应变值一般均超过屈服极限。
The most dangerous point is at the root of the first engaged tooth of a joint. Generally, the biggest values of stress and strain may exceed the yield limit.
然后，根据所拟合的曲线，计算出了B楞瓦楞纸板的缓冲系数-最大应力曲线。
Then, according to the fitting curve, the cushion coefficient-max stress curve of corrugated paperboard with B-flute was calculated.
主要利用ANSYS软件对连杆应力进行分析，计算出连杆的最大应力和应变。
ANSYS software will be applied to analyze the stress of connecting rod, and the maximum stress and displaced shape are showed.
确定发动机零部件的最大应力应变循环是进行零部件寿命研究的重要内容之一。
To determine the principal maximal stress-strain cycle of engine components is an important step in research on engine components' life.
文章利用解析法研究了材料热膨胀系数对温度场中太阳电池板最大应力的影响。
The effect of thermal property on the stress distribution in solar panel in thermal field is studied analytically.
优化的目标函数是最大应力最小，设计变量是圆角附近设计单元控制节点的坐标。
Maximum stress ACTS as objective function. Coordinates of control nodes of design elements near the fillet are regarded as design variables.
计算结果表明，运用非线性理论求得的最大应力比常规设计要小15 ~ 20%。
The calculate data show that the maximum normal stress given by the nonlinear method is 15-20% less than that by linear one.
用极值法求出最大应力的位置和大小，为木材和人造板在建筑上的应用提供理论依据。
With limit value method, the paper has evaluated the largest stress and its site, and supplied theoretical basis for use of wood based material in architectural engineering.
通过数值分析，给出了内外圈和接触体的应力分布曲线以及接触产生的最大应力位置。
By numerical analyzing, both the maximum stress position generated by contacting, and the stress distributing curve of inner-outer RACES and contacting body were presented.
通过比较表明，有限元结果和试验结果吻合得较好，最大应力均发生在圆角附近区域。
The paper proposes a finite element model for predicting the stress distribution based on experiments.
研究结果表明，该方法可以较准确地确定影响零部件寿命主要因素的最大应力应变循环。
The result shows that using the residue stress we can calculate accurately the maximal stress-strain cycle, which is the main factor influencing component life.
本文根据平面应力状态的解析式，推导出了一种判别最大应力极值所在方向的简捷方法。
Based on the analytical formula of the plane stress state, a simple and direct distinguishing method is derived with regard to the direction in which the maximal extremes lie.
在形变速率相同的条件下，随变形温度的升高，试样内部最大形变抗力及最大应力呈下降趋势。
The inner maximum resistance force and the maximum stress of the specimen decreases as the deformation temperature increasing.
利用最大应力强度准则，得到了单一螺旋缠绕及螺旋加环向缠绕圆环压力容器爆破压强的计算式。
According to the maximum stress strength criterion, the burst pressure formula for the single spiral and the spiral with hoop filament-wound toroidal pressure vessel were obtained.
结论实现火车轮轴的优化设计，优化后轮轴的最大应力均小于屈服应力，满足我国铁路的标准要求。
Optimized design of rail wheel and axle is finished. Conclusion This result satisfies our national railway standard. The maximum stress is less than the yield stress.
应用推荐