高强度的碳纤维具有最大刚度，但是比大多数玻璃纤维更为纤细，因此也更难灌注。
High strength carbon fibers give maximum stiffness but are also finer than most glass fibers and thus more difficult to infuse.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
通过对其疲劳性能的实验研究，发现裂纹扩展速率的大小及刚度的下降与加载的最大循环应力密切相关的规律。
The fatigue properties were researched and found that the crack propagation velocity and the decline of rigidity were related to the maximum cycle stress.
腰椎后前的刚度之间的关系非最大活性的肌肉和腰伸肌。
The relationship between submaximal activity of the lumbar extensor muscles and lumbar posteroanterior stiffness.
通过分析得出了被加固梁最佳支承刚度的计算方法，以及与其对应的最大承载力的计算方法。
This paper gives a method of calculating the optimum support rigidity of the reinforced beam and calculating the corresponding greatest bearing capacity.
第七个锚朝向天花板而没有物理连接，它的增加使得沿着表面的双曲率最大化，因而嵌入了内在刚度。
A seventh extra anchor toward the ceiling, not physically connected, is added in order to maximize double curvature along the surface, and therefore embedding inherent stiffness.
本文就消能减震结构设计参数，即消能部件的支撑刚度、层间最大阻尼力与结构层间屈服力比值等恢复力模型参数的选取进行了讨论。
The design curves of equivalent damping ratio to the brace stiffness, and ratio of maximum damping force of the damping device to the inter-story yield shear force of the structure are proposed.
角刚度(又称弹性比力矩)及弹性件在最大摆角下的剪切应变是固体发动机柔性接头设计的重要指标。
Angular stiffness and elastomer shear strain on maximum swinging Angle are important indexes in flexible joint design of solid rocket motor.
再按刚度分配原则，可求出实际结构不形成机构体系可能承受的最大水平地震作用。
The maximum bearing horizontal seismic actions of a structure that mechanism system is not formed are calculated based on principle of stiffness distribution for a structure.
对组合梁施加预应力后，可以减小弹性范围内的最大挠度，增强梁的刚度；
After having been prestressed, the composite beams can reduce the maximum flexibility within the range of elasticity, and increase their stiffness.
对整个结构进行了变形分析，找出了其在危险状态下的最大位移，明确了其刚度状况。
Analyzing the deformation of entire structure, finding the most displacement in danger status then knowing the status of stiffness.
再根据刚度分配原则，可计算出整个结构不形成机动体系所能承担的最大水平地震作用。
The maximum horizonta1 seismic actions of a structure in which any of mechanism system is not formed can be further ca1culated based on principle of stiffness distribution.
按气体轴承刚度最大准则优化了固有节流轴承参数。
The inherent throttle bearing parameters are optimized according to the maximum stiffness of aerostatic bearing.
对所有试件进行压缩刚度、扭矩刚度、最大扭矩等生物力学实验，观察不同截骨形状的稳定性。
So, such biomechanical experiments as compression rigidity, torsion rigidity and maximal torsion were carried out, and the steadiness of differently resected bones were observed.
这些选手采用独特的车身设计不包括石油带，最大限度地提高刚度，减少套管磨损升降。
These lifters feature an exclusive body design that does not include an oil band, maximizing rigidity and reducing lifter bushing wear.
因此，合理确定横梁安装位置而使动臂的强度、刚度最大，对动臂结构的合理性尤为重要。本。
So the rational position of cross beam is determined to ensure the highest strength and stiffness of boom and the most rational design of boom structure.
以结构的总重量最小和结构的总应变能最大为优化目标，以导管的平均直径和壁厚作为设计变量，考虑强度、刚度和稳定等约束条件。
Total weight and seismic strain energy of the structure were selected to be optimal objectives. Average diameter and wall thickness of the structural element were taken as design variables.
利用有限元法，对绉片机机架的强度和刚度进行分析，找出机架在正常工作状态下的最大变形和最大应力发生的位置，针对机架的薄弱环节采取相应的措施可以得到更加稳定的机架。
The strength and stiffness of crepper frame is analysed by finite element method in this paper, through which the location of the maximal distortion and stress can be found in normal conditions.
瞬态动力学分析通过考察联轴器传递转矩过程中的最大应力、最大位移及其发生部位来分析联轴器的动态刚度和强度状况。
The transient dynamic analysis researched the dynamic stiffness and strength of the joint by investigating the maximum stress and strain when it transmits torque.
最大位移随桩的抗弯刚度的增加而减小，而最大弯矩受抗弯刚度的影响很小；
The maximum lateral displacement decreases when the pile stiffness increases, while the maximum bending moment is hardly influenced by the pile stiffness.
并以辊系刚度最大为目标函数，对辊系尺寸进行了优化计算，提出了辊系尺寸的合理配置方法。
Taking roll system rigidity maximum as target function, the optimum calculation of roll system size has been carried out. The rational disposition methods of roll system is proposed in this paper.
在结构设计中，需要对梁的强度、刚度、稳定性等方面进行计算，其中绝对最大弯矩及位置的计算极为重要的。
The major role in the design of cantilever sheet pile is to determine the insert depth and the maximum bending moment.
在结构设计中，需要对梁的强度、刚度、稳定性等方面进行计算，其中绝对最大弯矩及位置的计算极为重要的。
The major role in the design of cantilever sheet pile is to determine the insert depth and the maximum bending moment.
应用推荐