最佳电流调节在任何级别没有可闻的噪声。
Best Current Regulation at Any Level, Without Audible Noise.
钕磁铁的N42提供了最佳平衡的耐用性和磁铁强度(电流输出)。
The N42 neodymium magnets provide the optimal balance of durability and magnet strength (current output).
通过实验确定了最佳参数，其中包括：离化电子电流和电压、加速电压、阻止电势、供气压力等。
The optimum parameters, such as electron current and voltage for ionization, acceleration voltage, retarding voltage, gas inlet pressure, were determined by experiments.
电流源变流器中，L C滤波器是滤除开关谐波的最佳结构。
In the current source transduce, LC filter is the best structure to filter the switching harmonic.
雷射驱动器将资料流的波形特性最佳化，并且提供适当的调变电流给雷射。
The laser driver optimizes the characteristics of data streams and provides the adequate modulation current to the laser.
采用中中值波形控制方法对钢进行焊接试验，确定了最佳的中值电流和中值时间。
The optimum median current and median time were found by experiment when welding steel using waveform with middle median phase.
经由将回路滤波器中的运算跨导放大器的规格做最佳化，一个电流最佳化的技术被提出。
A current optimization technique is proposed by making a specification optimization of the Operational Transconductance Amplifier in loop filter.
提出了存在着电流密度与进料量的最佳组合。
The optimum combination between electric current density and input quantity is put forward.
在最佳工作条件下，给出了集电极电流和集电极——发射极电压波形。
The waveforms of the collector current and collector-emitter voltage are also determined under the optimum operation condition.
建立了一个导电加热切削最佳加热电流数据库，并将插值算法应用到该数据库中。
An optimum heating current data base in Electric Hot Machining is constructed in this paper and an inserted algorithm is applied in this base.
电机双端轴承绝缘并且电机轴碳刷接地，可构成对轴承电流的最佳防护。
The optimal protection for bearing current was reached by the insulation of both ends of bearing and grounding of carbon brush of motor shaft.
分析测量误差与调制电流大小的关系，进而确定短距离测距的最佳实验条件。
The measurement error is found to decrease with the increase of the modulation current and this relation is applied to finding the optimum experimental condition for the short distance measurement.
为了抑制电流换相期间的浪涌电压，逆变器采用最佳相角控制。
The inverter uses opetimal phase angle control scheme to suppress the surge voltage during the commutation of current.
大于最佳值会导致短路电流的微小上升和开路电压的大幅下降；
The mobility larger than the optimal value will lead to a small increase in the short circuit current.
提出了减小电机换向冲击电流的延时通电控制方式，讨论了实现该控制方式的可行性和最佳参数优化。
A controlling method of "late switch on" is put forward, which can reduce the impulse current of linear motor in the turnback period. The reliablity of the controlling method is discussed.
对其电化学过程和化学氧化过程分别进行了研究，并优化出了在高电流效率和高产率条件下的最佳反应条件。
The electrochemical and chemical steps were investigated separately in order to determine operating conditions providing a high current efficiency and high yield.
确定了最佳磁化强度时的激励电流。
The excitation current which bring about the optimum magnetic…
IGBT具有额定电压高、电流大，开关速度快，易于驱动等优点，是中-高功率变流器应用的最佳选择。
IGBT has a high rated voltage, current and switching speed, easy to drive, is one of the best choice of high-power converter applications.
理论和实践表明，涓流充电、大电流充电、过充电和浮充电组合起来的充电方式，可达到最佳的效果。
Theory and practice indicate tiny stream flow, charge, large electric current charge, cross, charge and float way of charging combined to charge, can reach the best result.
电机双端轴承绝缘并且电机轴碳刷接地，可构成对轴承电流的最佳防护。
The optimal protection for bearing current was reached by the insulation of both ends of bearing and grounding of carbon brush of motor shaf…
通过讨论输入失调电流对集成运算放大器输出的影响，推导出集成运算放大器外围阻抗的最佳取值关系。
After discussing how the input offset current influences the output of operational amplifier, the optimal relationship between peripheral impedance is obtained.
在电动机实际工作的电压和电流约束条件下，提出了多相永磁电动机的一种最佳转矩控制方法，该方法能够使电动机在给定的控制电流下获得最大的输出转矩。
Under the actual operation lim its of motor voltage and current , a high-efficiency optimum torque control met hod for poly-phase PMSM is proposed.
气保焊的最小电流40A，是焊接超薄板的最佳选择；
Minimun welding current is 40A, is the best choice for sheet.
系统地研究了磁场强度H和焊接电流I对钴基堆焊合金堆焊层硬度和耐磨性的影响，发现当磁场强度H和焊接参数相匹配时，焊缝组织才能获得最佳的细化效果。
This paper discussed the influence of the magnetic field intensity H and welding current I on the hardness and the wear resistance of the Co-based alloys surfacing lager.
束电流与束电压确定，存在最佳的磁场使离子噪声幅度最小。
There exists on optimal value of magnetic focusing field and beam voltage, which can minimize the ion noise amplitude.
并结合现场测试条件，提供了最佳抛光电流密度。
Theoptimurn electric current density for polishing was given incomhnation with measurement in situ.
并结合现场测试条件，提供了最佳抛光电流密度。
Theoptimurn electric current density for polishing was given incomhnation with measurement in situ.
应用推荐