霍尔叶片传感器主要用于检测汽车发动机曲轴位置和转速，此外还可用于检测无刷电机磁极位置及测速等。
The Hall-effect vane sensor is to be primarily used to sense the angle position and the speed of the crankshaft of the automotive engine, in addition to be used in brushless DC motors.
百分表及通用百分表托架必须通过螺钉固定在气缸体上，位置与曲轴臂相对。
Dial gauge with universal dial gauge bracket must be screwed to the cylinder block and placed against the crank arm.
飞轮标记与凹口可以用来确定阀门与点火装置系统的位置，其要根据曲轴的规定位置来确定。
The flywheel marks and indentation are used for setting the valve and the ignition systems relative to prescribed position of the crankshaft.
介绍了曲轴连杆轴颈磨削的原理，对其常见的位置误差现象的形成原因进行了分析，并提出了相应对策和办法。
The grinding principle of crankshaft journal is introduced, the formation reason of position error is analyzed in detail, and the corresponding measures are proposed as well.
汽车内泄漏污染物的四个位置是燃油箱、化油箱、曲轴箱和尾管。
The four places in the automobile from which pollutants can escape are the fuel tank, carburetor, crankcase and tail pipe .
(上止点)-当活塞离曲轴最远时，曲柄和活塞的位置。
TDC (top dead center) - the position of the crank and piston when the piston is farther away from the crankshaft.
传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。
The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.
提出了两种曲轴齿轮轴颈键槽位置误差的检测方法。
Two kinds of inspection methods of the position error of key slot an gear journal of crankshaft have been proposed.
研究结果表明，改变曲轴的质量特性参数对机体的干扰力有不同程度的影响，其质心位置对惯性力平衡有较大的影响。
The results show that modifying mass parameters of crank have different effects on the cylinder block, especially the arrangement of counterweight.
曲轴上凸轮凸角的位置使气门在恰当的时侯开关，以便与气缸的工作顺序相一致。
The CAM lobes are so positioned on the camshaft as to cause the valves to open and close in the cylinders at the proper time with respect to the actions taking place, in the cylinders.
汽车内泄漏污染物的四个位置是燃油箱、化油箱、曲轴箱和尾管。
The four places in the automobile from which pollutants can escape are the fuel tank, carburetor, crankcase and tail pipe.
从曲轴上获取活塞位置信号时，所使用的上止点传感器及曲轴转角传感器在结构上趋向于一体化。
When obtain piston position signal from Crankshaft, Top Dead Center Sensor and Crankshaft position Sensor tend to be integrative in structure.
一曲轴传感器(15)输出一曲轴信号，该信号中包含指代转角的部分和指代参考位置的部分。
A crank sensor (15) outputs a crank signal including an Angle indicating part and a reference position indicating part.
位置正时是指ecu通过对转速信号的处理，判定当前工作缸号及计算曲轴当前位置的过程。
Location synchronization is the process that the ECU processes speed signal, and determines the current working the number of cylinder and the current location of crankshaft.
汽缸内多个汽缸容积由曲轴带动下旋转的活塞在汽缸容积的位置角度变化而不同。
The plurality of cylinder volumes in the cylinder are different according to the Angle change of the position of the piston rotating in the cylinder volumes under the drive of a crankshaft.
汽缸内多个汽缸容积由曲轴带动下旋转的活塞在汽缸容积的位置角度变化而不同。
The plurality of cylinder volumes in the cylinder are different according to the Angle change of the position of the piston rotating in the cylinder volumes under the drive of a crankshaft.
应用推荐