建立了单纯由幅度谱值构成的对称连杆曲线的特征参数。
The characteristic values are established of a symmetric coupler curve consisting only of the amplitudes.
根据实测曲线，对建立的线性三元件模型进行参数拟合。
Based on the experimental curve, parameters are fitted for an established linear three elements mechanical model.
建立了橡胶轮低地板拖车转向架车辆动态曲线通过分析模型并确定了有关的动力学参数。
In this paper, the dynamical model for vehicle with the rubber-tired and low-floor bogie is established and the dynamical parameter of vehicle is gotten.
采用回归分析方法建立了参数与土壤物理特性间的函数关系，为采用土壤颗粒组成等土壤物理特性确定土壤水分特征曲线提供了指导。
A fitted relationship between the parameters and the soil texture was established, with which the model parameters of soil water retention curves can be predicted by the soil physical characteristic.
建立了单纯由幅度谱值构成的对称连杆曲线的特征参数。
The characteristic values of a symmetric coupler curve are established to be consisting simply of the amplitudes.
利用所建立的数学模型，采用计算机模拟的方法，得到了主要参数间的静态关系曲线，并分析了系统动态特性。
A static relations curve of the main movement parameter is given by means of computer simulation and by an established mathematical model, and the system dynamic characteristic analyzed.
提出了热油管输过程热经济性定义、评价参数、评价方法和建立动态评价曲线的方法，并进行了实例评价。
Based on a thermal analysis, the definition and assessment parameters of heating economics for heat oil pipeline were brought forward in the paper.
采用状态空间平均法建立了变换器平均模型，获得了关键电路参数的设计准则和变换器的外特性曲线。
By using the state-space averaging approach, the converter's averaging model is presented, and the design criterion of key circuit parameters and the output characteristic curve are given.
本文建立了复合材料疲劳寿命曲线的“有效缺陷模型”，阐明了模型中两个参数的物理意义。
The effective flaw model is developed to describe the S-N curves of composite materials. The two fitted parameters in the model have certain physical meaning.
在建立了由DTA曲线求取任一时刻转化率和反应速度方法的基础上，求得动力学参数。
Based on the methods for calculating directly the conversion and reaction rate at any time from a DTA curve, the kinetic parameters of gasification are obtained.
本文研究了加工经可控曲率修正的蜗轮齿面的滚刀设计问题，建立了相应的数学模型，并应用计算铲磨蜗轮滚刀刃形曲线的单参数包络法，求出铲磨砂轮截形曲线。
This paper studies the relief grinding problem of the hob of point contact worm gear drive and puts forward a one-parameter enveloping method to calculate the axial profile of relief grinding wheel.
本文提出了一种建立空间列表曲线的数学模型的方法——空间三次参数样条曲线法。
This paper proposes a method to build the mathematical model of special spline curve.
采用响应面法建立了表示比吸能随材料参数而变化的曲面，和高次多项式拟合时的相对误差曲线。
Then the response surface method(RSM) is utilized to establish the response surfaces or curve of SEA vs. material parameters and the curves of relative error in high-order polynomial fitting.
基于这种基函数，建立了一种带多个形状参数的二次双曲多项式曲线，该类曲线对于非均匀节点为C1连续。
Based on the basis functions, quadratic hyperbolic polynomial curves with multiple shape parameters are constructed. These curves are C1-continuous with a non-uniform knot vector.
将从动件的直线往复移动和定点往复摆动用虚拟摆动统一表示，采用单参数包络曲线理论建立直动和摆动从动件平面盘形凸轮轮廓的统一数学表达式。
In this article, the unified profile expression of the planar CAM mechanism with translation or oscillation follower is established based on the theory of envelopes for 1 parameter family of curves.
首先根据工作原理建立了数学模型，然后从分析设计理论误差出发，提出了以虚拟样机技术作为辅助手段的贴标机凸轮轮廓曲线的参数化的设计算法。
Advance modern means and research method such as digital thehnology, virtual prototype(VP), dynamic design is utilized on the theory study during the course of new model equipment's research.
建立了参数化的三维模型，并用反转法绘制了摆动输出凸轮的轮廓曲线。
The parametrical 3-D model is built and the output cam profile is drawn.
建立了参数化的三维模型，并用反转法绘制了摆动输出凸轮的轮廓曲线。
The parametrical 3-D model is built and the output cam profile is drawn.
应用推荐