锥齿轮和曲柄轴都在油室内，除定期检查外，无需专门关注。
The bevel gears and the crank shafts are totally enclosed in oil chamber and require no attention, except periodical checks.
要启动发动机，首先得点燃热管，再转动曲柄轴，发动机便启动，这些准备工作只需一分钟。
To start the engine, one must first light the small flame beneath the hot ignition tube and crank the engine once using the crank; these preparations take only a minute.
发现物涉及到不充分的，纠正措施，用来避免重复的失效，那是关于，9号大曲柄轴，在第一号柴油机。
Finding involved inadequate corrective actions to prevent repeat failure of the number nine main crank shaft bearing on emergency diesel generator number one.
设计的新型三环减速器主要由圆弧齿同步齿形带、小带轮、大带轮、曲柄轴、传动环板、输出轴、外齿轮和箱体等组成。
Newly developed three ring gear reducer is comprised of synchronous belt, big and small pulleys, crankshaft, drive ring plate, output shaft, external gear and case.
文章对其几何尺寸与平衡参数进行了优化设计，证实该机型曲柄轴的均方根扭矩比异相型减少了31.2％，最大扭矩减少了35.3％，平衡效果显著。
The geometric dimensions and balance parameters of the beam pumping units are optimized. As a result, Me is re- duced 31.2% and Mnmax is reduced 35.3% than phased balance.
为实现在将曲轴水平放置绕主轴转动条件下，对单拐或多拐曲轴的主轴和曲柄轴进行激光淬火和激光熔覆，建立了激光作用于曲拐表面形成螺线时的光斑轨迹方程。
It aims to realize the laser quenching and cladding for the principle axis and crank of single or more crank while the crankshaft is laid horizontally and rotating around the principal axis.
转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。
Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.
由于偏心轮可装于轴的任何部位，不必把主轴作成曲柄。
Because an eccentric can be attached anywhere along a shaft, it is unnecessary to form any part of the shaft into a crank.
为了使测量双轴摇摆台实现高频率的运动，机械结构上设计采用了一种新型的曲柄、连杆、万向节机构；
A new mechanical structure with winch, staff and gimbal is used to develop a gyrometer test table to realize the high frequency of the operation.
同常规型游梁式抽油机比较，该机型可以显著降低曲柄输出轴的最大扭矩，减小甚至消除负扭矩，在降低能耗的同时改善了减速箱的受力状况。
Compared with conventional beam pumping unit, the swing-rod beam pumping unit can reduce the maximum crank axle torque markedly, reduce and even eliminate negative crank axle torque.
在机架上设有摇臂驱动电机，一曲柄及曲柄连接杆铰接在该电机的轴和第一平行连杆之间。
The frame is provided with a rocker driving motor, a crank and a crank connecting rod hinged between the motor and the first link rod.
旋转运动是由曲柄、三角架导向轴完成的。
Rotation is realized by the brace and the triangle oriented axis.
一个稍微便宜的选择对于那些在碳曲柄看的是“标准”下一个型号的钢轴的功能，不重得多，约700克环取决于所选择的。
A slightly cheaper option for those looking at carbon cranks is the "standard" Next model which features a steel axle and is not much heavier, being around 700 grams depending on ring choice.
单独使用滚轮时，可在并列或者前后串列的两个滚轮的转轴装上曲柄，曲柄顶端有踏板轴。
When using the idler wheel only, fix the brace on the axes of the two idler wheels in paratactic or in series and the top of brace has footplate axes.
建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩；
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩；
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
应用推荐