方法：用拉力机、显微硬度机测试。
Methods: Tension test machine and microhardness tester were used.
材料横截面显微硬度连续变化。
The cross section micro hardness of the material changes continuously.
动态超显微硬度仪测试材料的硬度。
Hardness was counted by Dynamic Ultra Micro Hardness Tester.
用显微硬度仪测试了试样的显微硬度。
表面显微硬度较未处理的样品明显提高。
The surface microhardness was substantially increased compared with the untreated.
界面区显微硬度显著提高。
利用显微硬度试验机来测量表面显微硬度。
Microhardness on the surface layer were measured by microhardness testing machine.
测试了涂层的显微硬度。
研究了热处理对镀层显微硬度和磁性能的影响。
The effect of heat treatment temperature on the microhardness and magnetic properties were investigated.
合金的显微硬度变化趋势不符合超塑性波动公式。
In addition, the trend of microhardness variety could not accord with the ultra-plastic wave formula.
对经时效处理后的含铜高纯钢进行了显微硬度测试。
Microhardness testing during aging treatment in high purity steel bearing copper was carried out.
分析研究了喷丸强化处理前后的显微硬度和表面粗糙度。
The microhardness and surface roughness of specimens before and after shot peening was studied and analysed.
本文还通过显微硬度试验测得界面过渡环的性状及范围。
The microhardness test was used to determine the behaviour and the extent of the interfacial transition ring.
结论：不同材料的光敏树脂其聚合后的显微硬度存在差异。
Conclusion There was a significance difference on micro-hardness of light-cured composite resins.
当稀土金属盐加入量为2%时镀层密度最大、显微硬度最高。
When the RE metal salt was 2%, the coating had the best density and hardness.
目的观察不同浓度氟泡沫对脱矿牙釉质表面显微硬度值的影响。
Objective To investigate the influence of fluoride foam of different concentration on microhardness of demineralized enamel surface.
研究还发现接头显微硬度、平均抗拉强度介于黄铜与紫铜之间。
It was also discovered that the micro-hardness and mechanical properties were between that of copper and brass.
结果表明，工艺参数对冶金层显微组织及显微硬度有很大的影响。
The results show that the parameters have great effect on microstructure and microhardness of the coatings.
激光表面改性层显微组织与显微硬度受激光处理工艺参数的控制。
The microstructure and hardness of the laser modified surface are governed by the laser processing parameters.
测定了不同工艺条件下获得的浸渗层深度和浸渗层显微硬度的分布。
The depth and microhardness distribution of alumetizing layer obtained on different technical conditions were measured.
分别以应力分析仪和显微硬度仪测试两组试件的挠曲强度和硬度值。
The flexural strength and hardness of the specimens were tested with an instron testing machine and a microhardness tester.
本文对亮条的断口特征、金相组织、化学成分和显微硬度进行了分析。
This paper analyzes the fracture appearance, microscopic structure, chemical composition and micro-hardness of the bright ghost structure.
显微硬度测试表明，对相同成分合金，非晶态的显微硬度值比晶态的低。
The microhardness value of the amorphous alloy is lower than that of the crystalline alloy with the same composition.
脉冲参数对显微硬度和拉伸强度的影响符合相似的规律，但也有所不同；
The effect of pulse parameters on micro-hardness and stretch strength correspond to similar law, but different slightly.
阐述了一种纳米尺度下测试材料显微硬度的试验方法——深度硬度试验法。
This paper presents a micro-hardness testing method, namely depth-hardness testing with nanometer scale.
双程磨削淬硬可使表面硬化层深度及其均匀性、显微硬度及耐磨性得到进一步提高；
The depths and its uniformity of the surface hardened layer, its microhardness and wear resistance are further improved under two-passes grinding.
在合适的电刷镀工艺下，镀层表面平整、光滑，具有较高的显微硬度、耐蚀性和结合强度。
The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process.
在合适的电刷镀工艺下，镀层表面平整、光滑，具有较高的显微硬度、耐蚀性和结合强度。
The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process.
应用推荐