文章就回扫变压器的早期失效现象进行了探讨。
The early failure phenomena of flyback transformer was discussed in this paper.
介绍了冷轧支撑辊及工作辊早期失效的主要原因。
The causes of failure in early stage of work roll and backup roll for cold mill were discussed in the paper.
四辊轧机的花键轴服役四个月便发生了早期失效。
The earlier period failure of the spline shaft for a 4-roll rolling mill occurred after an operating period of 4 months.
文中对齿轮联轴器的连接螺栓的早期失效进行了分析。
Moreover, in this paper we analyse the initial failure of bolt connection in gear couplings.
本文适当地讨论了早期失效后假体取出及翻修的技术。
The technical aspects of the device explantation are discussed as well as issues pertinent to early failure.
齿轮在运转过程中出现偏载是导致早期失效的主要原因。
The main cause of early failure of the gear was the leaning load on operation.
某厂铝合金烤盘压铸模因模面出现大面积龟裂而早期失效。
Large area crack appearing on the surface of the aluminium alloy bakeware casting dies causes its early failure.
密封铅酸蓄电池内部失水是引起电池早期失效的主要原因。
The premature failure in VRLA battery mainly attributed to the inner water loss.
检查机械部件，防止因设备事故而导致轧辊非正常早期失效。
Check mechanical components, prevent the roll 'abnormal invalidation caused by accidents of equipment.
进口轴承材料的冶金质量曾经是影响滚动轴承早期失效的主要因素。
Imported bearing materials have been affecting the metallurgical quality of early bearing failure of the main factors.
研究了因不可逆硫酸化引起早期失效铅酸蓄电池容量恢复的可行性。
The feasibility of capacity recovery of sulphated lead acid battery(premature capacity loss)was studied.
结果表明，冷却水管发生早期失效是由于构件发生应力腐蚀开裂所致。
The results show that the early failure of the cooling pipe was caused by the stress corrosion cracking in the components.
机械密封产生变形会严重影响其工作性能，甚至导致磨损和早期失效。
The deformation of mechanical seals would seriously affect their working performance, even resulting in wear and early stage failure.
指出冷轧工作辊早期失效主要形式为剥落，其原因为局部过热和过载。
It is indicated that the early main failure forms of cold work roll is spalling caused by local overheat and overload.
结果表明，波纹膨胀节发生早期失效是由于构件发生应力腐蚀开裂所致。
The results show that the early failure of the corrugation expansion joint was results from the stress corrosion cracking in the components.
介绍了几只彩色显像管早期失效的性能特征和对其失效原因的诊断过程。
The paper introduced the early stage lapse performance characteristics of several color picture tubes and the diagnoses of their lapse causes.
本文介绍了一批彩显管早期失效的性能特征和对其失效原因的诊断过程。
The text introduced a set of color picture tubes early stage lapse performance Characteristic and the diagnose course of their lapse cause.
模具钢原材料冶金缺陷是先天性不足，是导致模具寿命短和早期失效致命伤。
Metallurgy defects of original material steel used by die is natural defects, which leads to short life cycle of die and invalidation in the early stage.
本文对武汉纺织器材厂生产的梭子底板弹簧早期失效的原因进行了全面的分析。
This paper makes a detailed analysis on the causes of carly failure of the bed plate spring for the shuttle.
针对某电厂异种钢焊接接头高温早期失效的过热器管件进行了调查研究和失效分析。
The early losing effectiveness causes of the superheater pipe welding joint were investigated and analysed.
本文讨论了在逆变电焊机中不同用途的电容特性及选用规则，以及预防早期失效的对策。
The capacitance characteristic rule for different use in the converting welder is discussed in the paper, and the countermeasure for protecting early failure is put forward.
对高风压潜孔钻头使用时钻头体崩块、掉齿等早期失效情况进行分析，找到其失效原因。
The failure cause was found by analyzing high pneumatic down-the-hole bit bursting crack and the other reasons in the early stage.
综述双极器件和双极线性电路在低剂量率辐射环境下的增强损伤，它可引起系统的早期失效。
The enhanced damage was summarized for bipolar devices and bipolar linear circuits in the radiation environment of low dose rate. It could cause the early failure of systems.
结合现场实例，进行了振动压路机驱动桥弧齿准双曲面齿轮早期失效分析和热处理技术评价。
Combined with the practical examples, the premature failure analyses for the hypoid gears of driving axle of vibratory compactor and evaluation of heat treatment technique were performed.
薄/超薄芯片的碎裂占据IC卡早期失效的一半以上，其失效模式、失效机理亟待深入研究。
The fracture of thin/ultra-thin silicon dies accounts for half of the failures of IC cards, and its failure modes and failure mechanism are not well understood then.
针对部分高速钢刀具在热处理过程中及用户使用时，因早期失效而损坏的原因进行了分析研究。
A study on the reasons why the cutting tools made from high-speed steel materials were damaged easily when used by users.
通过对安棚、赵凹区块钻具早期先期失效现状调查，得出了钻具早期失效的主要模式及产生原因。
By means of the survey at Anpeng and Zhaowa Blocks, the main modes and the causes of drilling tool failure in earlier period are found out.
根据检测试验结果，分析了导致彩色显像管管座发生偶发性早期失效的原因，以及相应的解决措施。
The cause and relative solution of accidental early failure of color tube holder was analyzed based on the measured results.
针对真空挤出机主轴轴承早期失效严重的情况，运用模糊可靠性设计理论对轴承的寿命进行了分析。
In consideration of the case which de-airing extruder roll bearing was seriously fail in the earlier stage, fuzzy reliable design theory is applied to analyze it.
针对真空挤出机主轴轴承早期失效严重的情况，运用模糊可靠性设计理论对轴承的寿命进行了分析。
In consideration of the case which de-airing extruder roll bearing was seriously fail in the earlier stage, fuzzy reliable design theory is applied to analyze it.
应用推荐